E 56 E E E TASK 77-00-00-810-859
N1 Mismatch during Flex Take Off on Engine 1 or 2
1. Possible Causes
_______________
- PS12 line
- engine identification plug
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU)(4000KS)
3. Fault Confirmation
__________________
A. Test
(1) Not applicable, the fault is evident.
4. Fault Isolation
_______________
A. If the fault symptom is identified by the crew observation: N1 mismatch during flex take off:
(1) Do the trouble shooting procedure on the engine with the lowest N1 actual.
(2) On this engine do a check of the PS12 line for dents, cracks or wear. If you find any damage, replace the PS12 line.
(3) Make sure that all piping connections are correctly tightened. If they are loosen, tighten them.
(4) If you find no damage on the PS12 line:
- disconnect the PS12 line from the ECU
- blow filtered dry air or nitrogen from the ECU (4000KS) side fitting into the PS12 line to clear it in case of any blockage
- clean the weep hole with a non metallic wire (max diameter: 0.5 mm).
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page 241
E E Nov 01/04 ERE
ECES E 56 E E E (5) If the fault continues:
F 『
E C F M E
E E
- do a check of the engine LRU identification screen with the CFDS to see if the engine rating coded through the engine identification plug is correct.
(a) If the rating is not correct:
- replace the engine identification plug.
(b) If the rating is correct:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
B. After the subsequent flight, make sure that the fault does not continue.
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page 242
E E Nov 01/04 ERE
ECES
F 『
E C F M E
E E
E 56 E E E TASK 77-00-00-810-860
N1 Mismatch during Take Off on Engine 1 or 2
1. Possible Causes
_______________
- PS12 line
- engine identification plug
- ECU (4000KS)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU)(4000KS) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU)(4000KS)
3. Fault Confirmation
__________________
A. Test
(1) Not applicable, the fault is evident.
4. Fault Isolation
_______________
A. If the fault symptom is identified by the crew observation: N1 mismatch at take off:
(1) Do the trouble shooting procedure on the engine with the lowest N1 actual.
(2) On this engine do a check of the PS12 line for dents, cracks or wear. If you find any damage, replace the PS12 line.
(3) Make sure that all piping connections are correctly tightened. If they are loosen, tighten them.
(4) If you find no damage on the PS12 line:
- disconnect the PS12 line from the ECU
- blow filtered dry air or nitrogen from the ECU (4000KS) side fitting into the PS12 line to clear it in case of any blockage
- clean the weep hole with a non metallic wire (max diameter: 0.5 mm).
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page 243
E E Nov 01/04 ERE
ECES E 56 E E E (5) If the fault continues:
F 『
E C F M E
E E
- do a check of the engine LRU identification screen with the CFDS to see if the engine rating coded through the engine identification plug is correct.
(a) If the rating is not correct:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(84)
