R b_ If no evidence of contact is found:
R - replace the J10 Harness (Ref. AMM TASK 73-21-50-000-043)
R and (Ref. AMM TASK 73-21-50-400-043)
R (3) If fault continues during the subsequent flights:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref.
R AMM TASK 73-21-60-400-001).
F 『
∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A218
EEFF : ALL E
E E May 01/03
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R C. If the failure message ECU (B CHANNEL) is confirmed:
R - do a check of the J10 harness connection at the control alternator:
R (1) If the connection is loose:
R - tighten the connection by hand plus one eighth of a turn.
R NOTE : Soft nose pliers may be used if necessary.
____
R (2) If the connection is tight:
R - disconnect the J10 harness from the alternator stator (ALT-B)
R (located in the left core compartment).
R (a) Visually examine the alternator stator receptacle and the J10
R harness connector for damaged pins or contamination (Ref. AMM
R TASK 73-21-50-210-002).
R 1_ If harness or alternator stator connector is damaged:
R - repair or replace as required.
R 2_ If no damage is found:
R - do an electrical resistance test through the alternator
R stator connector between:
R . pins 2 and 5 (<1 Ohm)
R . pins 3 and 5 (<1 Ohm)
R . pins 4 and 5 (<1 Ohm)
R . pins 5 and the ground (>10 Megohms)
R 3_ If the resistance values are out of the specified limits:
R - replace the alternator stator (Ref. AMM TASK 73-21-30-000-R 001) and (Ref. AMM TASK 73-21-30-400-001).
R 4_ If the resistance values are in the specified limits:
R - reconnect the J10 harness to the alternator stator.
R - disconnect the J10 harness from the ECU (4000KS) receptacle.
R - Visually examine the ECU (4000KS) receptacle and the J10
R harness connector for damaged pins or contamination (Ref.
R AMM TASK 73-21-50-210-002).
R a_ If harness connector or ECU receptacle is damaged:
R - repair or replace as required.
R b_ If no damage is found:
R - do an electrical resistance test through the J10 harness
R between:
R . pins 5 and 13 (<1 Ohm)
R . pins 5 and 14 (<1 Ohm)
R . pins 5 and 15 (<1 Ohm)
R . pins 5 and 4 (>10 megohms)
R . pins 13 and 4 (>10 megohms)
R . pins 14 and 4 (>10 megohms)
R . pins 15 and 4 (>10 megohms)
R . pin 5 and the ground (>10 megohms)
F 『
∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A219
EEFF : ALL E
E E May 01/03
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
R
R * If the resistance values are out of the specified
R limits:
R - replace the J10 harness (Ref. AMM TASK 73-21-50-000-
R 043) and (Ref. AMM TASK 73-21-50-400-043).
R
R * If the resistance values are in the specified limits:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-
R 001) and (Ref. AMM TASK 73-21-60-400-001).
R D. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not
confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page A220
E E May 01/03 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
TEMPERATURE - FAULT ISOLATION PROCEDURES
________________________________________
TASK 77-20-00-810-803
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(163)
