F 『
E C F M E
E E
E 56 E
E E
B. If the test confirms the fault:
- do a check of the circuit breaker 1EV status.
(1) If the circuit breaker is open:
- close the circuit breaker 1EV.
(2) If the circuit breaker is closed:
- do a check for 115VAC on the pin AC/2 of the EVMU (Ref. ASM 77-33/02).
(a) If there is 115VAC:
- replace the EVMU (2EV), (Ref. AMM TASK 77-32-34-000-042) and (Ref. AMM TASK 77-32-34-400-042).
(b) If there is no 115VAC:
- do a check and repair the wiring from the circuit breaker 1EV to the pin AC/2 of the EVMU (2EV) (Ref. ASM 77-32/02).
1 If the fault continues:
_
- replace the C/B-ENGINE/ENG1 AND 2/EVMU (1EV)
C. Do the operational test of the Engine Vibration Monitoring Unit (EVMU) through the Centralized Fault Display System (CFDS) (Ref. AMM TASK 77-32-34-710-040).
5. Close-up________
A. On the ECAM control panel, set the UPPER display and LOWER display
potentiometers to OFF (Ref. AMM TASK 31-60-00-860-002).
Put the aircraft back to its initial configuration.
F 『 EEFF : ALL E ∞∞77-30-00∞∞∞∞∞∞∞∞∞∞Page 205
E E Aug 01/04 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
TASK 77-30-00-810-805
Loss of the N1 Vibration Indication on Engine 1
1. Possible Causes
_______________
- EVMU (2EV)
- wiring from the EVMU (2EV) to the N1 speed sensor (4000EV)
- SENSOR-N1 ROTATIONAL SPD (4000EV)
- harness between the EVMU and the N1 speed sensor
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 71-00-00-710-009 Vibration Check
AMM 77-11-10-000-002 Removal of the N1 Speed Sensor (4000EV)
AMM 77-11-10-400-002 Installation of the N1 Speed Sensor (4000EV)
AMM 77-32-34-000-042 Removal of the Engine Vibration Monitoring Unit
(EVMU) AMM 77-32-34-400-042 Installation of the Engine Vibration Monitoring Unit (EVMU) ASM 77-32/02
3. Fault Confirmation
__________________
A. Test
Not applicable, you cannot confirm this fault on the ground.
4. Fault Isolation
_______________
A. If the Post Flight Report gives the maintenance message ENG1 N1 SPEED
SENSOR:
R - do a check for open or short to ground of the wiring from the EVMU
R (2EV) to the N1 speed sensor (4000EV) pins AA/8B, 7A to pins CC/1, 2
(Ref. ASM 77-32/02).
(1) If the wiring is not correct:
- repair the above wiring.
(2) If the wiring is correct:
- with the cable disconnected from the EVMU, do a resistance check of the EVMU between: pins 8B and 7A (40 to 80 Ohms).
(a) If the resistance values are in the specified limits:
- replace the EVMU (2EV) (Ref. AMM TASK 77-32-34-000-042) and (Ref. AMM TASK 77-32-34-400-042).
F 『 EEFF : ALL E ∞∞77-30-00∞∞∞∞∞∞∞∞∞∞Page 206
E E Aug 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
(b) If the resistance values are out of the specified limits: R - with the connector CC disconnected from the N1 speed sensor, do R a resistance check of the sensor between:
pins 1 and 2 (40 to 80 Ohms).
1 If the resistance values are out of the specified limits:
_
- replace the SENSOR-N1 ROTATIONAL SPD (4000EV) (Ref. AMM TASK 77-11-10-000-002) and (Ref. AMM TASK 77-11-10-400-002).
2 If the resistance values are in the specified limits:
_
- replace the harness between the EVMU and the N1 speed sensor (Ref. ASM 77-32/02).
B. Do the vibration check to get the vibration data (Ref. AMM TASK 71-00-00-710-009).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(186)
