- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and (Ref. AMM TASK 73-21-60-400-001).
b If the resistance values are out of the specified limits:
_
- replace the HJ8 harness (Ref. AMM TASK 73-21-50-000-041) and (Ref. AMM TASK 73-21-50-400-041).
B. Do the test given in Para. 3.A.
(1) No additional maintenance action is required if the fault is not confirmed.
(2) Repeat the fault isolation procedure if the fault continues.
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 270
E E Aug 01/99 E E ECES
E TASK 77-10-00-810-835
F 『
E C F M E
E E
E 56 E
E E
Loss of the Feedback Signal of the N2 Speed Sensor - Engine 2 - Channel A
1. Possible Causes
_______________
- SENSOR-N2 ROTATIONAL SPD (4001EV)
- ECU (4000KS)
- HJ7 harness
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific bristle brush
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2011 * stoddard solvent (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 73-21-50-000-040 Removal of the HJ7 Harness AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses AMM 73-21-50-400-040 Installation of the HJ7 Harness AMM 73-21-60-000-001 Removal of the Electronic Control Unit (ECU) AMM 73-21-60-400-001 Installation of the Electronic Control Unit (ECU) AMM 73-29-00-710-040 Operational Test of the FADEC on the Ground (with
Engine non Motoring) AMM 77-11-20-000-002 Removal of the N2 Speed Sensor (4001EV). AMM 77-11-20-400-002 Installation of the N2 Speed Sensor (4001EV).
3. Fault Confirmation
__________________
A. Do the operational test of the FADEC 2A on the ground (with engine non motoring) (Ref. AMM TASK 73-29-00-710-040).
F 『 EEFF : ALL E ∞∞77-10-00∞∞∞∞∞∞∞∞∞∞Page 271
E E Aug 01/99 ERE
ECES
F 『
E C F M E
E E
E 56 E
E E
4. Fault Isolation
_______________
A. The failure message is generated if channel A input from the N2 sensor is invalid or out of range.
(1) If the failure message N2 SNSR, J7, ECU* is not confirmed: R
R (a) No maintenance action is required.
(2) If the failure message N2 SNSR, J7, ECU* is not confirmed but is repetitive:
- disconnect HJ7 harness from the N2 sensor (N2-A connector).
R (a) Visually examine the receptacle and the connector for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_
- do a cleaning of the connector and receptacle using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
R
R (b) If the failure continues during the subsequent flights:
- replace the SENSOR-N2 ROTATIONAL SPD (4001EV) (Ref. AMM TASK
77-11-20-000-002) and (Ref. AMM TASK 77-11-20-400-002). R
R (c) If the failure continues during the subsequent flights:
- replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001) and
(Ref. AMM TASK 73-21-60-400-001). R
R (d) If the failure continues during the subsequent flights:
- replace the HJ7 harness (Ref. AMM TASK 73-21-50-000-040) and (Ref. AMM TASK 73-21-50-400-040).
(3) If the failure message N2 SNSR, J7, ECU* is confirmed: R - disconnect the HJ7 harness from the N2 sensor (N2-A connector).
R (a) Visually examine the receptacle and the connector for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_ R - do the electrical resistance test through the N2 sensor R (4001EV) (channel A) between:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(143)
