F 『
E C F M E
E E
E 56 E
E E
F 『 EEFF : ALL E Page 104∞∞77-CFDS ∞∞∞∞∞∞∞∞∞∞
E E Nov 01/04 ERE
ECES F E E WARNINGS/MALFUNCTIONS E 十 E E 十 E E 十 E E E E 十
F 『
E C F M E
E E
E 56 E
E E
R E E 十
R E E E E 十 E E 十 E E 十 E E 十 E E E T T 『E CFDS FAULT MESSAGES E FAULT E十 T T T 1 ISOLATION EESOURCE E MESSAGE E ATA ECE PROCEDURE E十 十 十 十 十 1EEIU2FADET3 SNSR, J13, ECU ENG2A E772310ESE772000 P 211EE E E E ET 810 806 E十 十 十 十 十 1EEIU2FADET495 SNSR, J13, ECU E772110ESE772000 P 204EE EENG2A E E ET 810 804 E十 十 十 十 十 1EEIU2FADET495 SNSR, J13, ECU E772110E1E772000 P 204EE EENG2A E E ET 810 804 E十 1 1 1 1 EEIDENT: EIU2FAD E E十 T T T 十 1 EEIU2FADET495 SNSR, J13, ECU E772110ESE772000 P 234EE EENG2B E E ET 810 827 E十 十 十 十 十 1 EEIU2FADET495 SNSR, J13, ECU E772110E1E772000 P 234EE EENG2B E E ET 810 827 E十 1 1 1 1 EEIDENT: EIU2FAD E E十 T T T 十 1EEIU2FADET5 SNSR, J13, ECU ENG2A E772200E3E772000 P 225EE E E E ET 810 812 E十 十 十 十 十 1EEIU2FADET5 SNSR, J13, ECU ENG2B E772200E3E772000 P 229EE E E E ET 810 823 E十 十 十 十 十 1EEIU2FADET5 SNSR, J13, ECU* ENG2BE772200ESE772000 P 229EE E E E ET 810 823 E十 十 十 十 十 1EEVMU EEVMU E773234E3E773000 P 222EE E E E ET 810 813 E1 1 1 1 1 E
F 『 EEFF : ALL E Page 105∞∞77-CFDS ∞∞∞∞∞∞∞∞∞∞
E E Nov 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
ENGINE INDICATING - GENERAL - FAULT ISOLATION PROCEDURES
________________________________________________________
TASK 77-00-00-810-823
Disagree between the EGT Indication and the ECU Output on Engine 1
1. Possible Causes
_______________
- EGT thermocouple
- CJ13 and HJ13 harnesses
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific bristle brush
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. CP2011 *
stoddard solvent (Ref. 70-30-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 73-21-50-210-002 Visual Inspection of the Wiring Harnesses AMM 77-21-10-000-008 Removal of the Upper Extension Lead R AMM 77-21-10-000-025 Removal of the Main Junction Box AMM 77-21-10-400-008 Installation of the Upper Extension Lead R AMM 77-21-10-400-025 Installation of the Main Junction Box
3. Fault Confirmation
__________________
A. Test.
(1) Not applicable.
F 『 EEFF : ALL E ∞∞77-00-00∞∞∞∞∞∞∞∞∞∞Page 201
E E Aug 01/04 E E ECES
E
F 『
E C F M E
E E
E 56 E
E E
4. Fault Isolation
_______________
A. The ECAM warning message ENG 1 EGT DISCREPANCY is generated if the cockpit indicated EGT and the EGT output selected from the ECU disagree.
(1) Disconnect harnesses from the EGT sensor receptacles, HJ13 and CJ13 (upper right hand and left hand thermocouple connectors, lower left hand and right hand thermocouple connectors).
R (a) Visually examine the receptacle and the connector for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
_ - repair or replace as required.
2 If no damage is found:
_
- do a cleaning of the connector and receptacle using a bristle brush with stoddard solvent (Material No. CP2011) (Ref. AMM TASK 73-21-50-210-002).
(2) Disconnect harnesses from the ECU (4000KS), HJ3 and HJ4.
R (a) Visually examine the receptacle and the connector for damaged R pins or contamination (Ref. AMM TASK 73-21-50-210-002).
1 If damage is found:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發動機指示(67)
