4. Fault Isolation
_______________
A. If the test gives the maintenance message DMC3 : PROGRAM PIN or DMC3 :
POSITION PIN: R - do a check for ground signals at DMC3 (1WT3) connector AB (Ref. AWM 31-R 61-30).
(1) If the wiring is incorrect:
- repair the wiring.
(2) If the wiring is correct:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
B. Do the test given in Para. 3.
Failure of One of the 6 DUs Detected by the DMC3
1. Possible Causes
_______________
- PFD-CAPT (2WT1)
- DMC-3 (1WT3)
- ND-CAPT (3WT1)
- DU-ECAM, UPPER (4WT1)
- PFD-F/O (2WT2)
- ND-F/O (3WT2)
- DU-ECAM, LOWER (4WT2)
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-60-00-740-002 EIS Input Test
AMM 31-63-22-000-001 Removal of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
AMM 31-63-22-400-001 Installation of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2)
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
ASM 31-61/04
3. Fault Confirmation
__________________
A. Test
Do the EIS input test (Ref. AMM TASK 31-60-00-740-002).
4. Fault Isolation
_______________
A. With the EIS DMC selector switch (18WT) on the SWITCHING panel (8VU) at CAPT/3.
(1) If the test gives the maintenance message DMC3 : RECONF WIRING and there is no CAPT PFD image:
- replace the PFD-CAPT (2WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(a) If the fault continues:
- do a check of the wiring from the CAPT PFD (2WT1) to the DMC1 (1WT1): . pins AA/21, 22 to pins AB/10B, 10C . pins AA/23, 24 to pins AB/10D, 10E (Ref. ASM 31-61/04).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 214
Feb 01/98 CES 1 If there is no continuity:
_ - repair the wiring.
2 If there is continuity:
_
- do a check and repair the wiring from the DMC1 (1WT1) to the DMC3 (1WT3): . pins AB/10F, 10G to pins AB/9D, 9E . pins AB/10H, 10J to pins AB/9B, 9C (Ref. ASM 31-61/04).
a If the fault continues:
_
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(2) If the test gives the maintenance message DMC3 : RECONF WIRING and there is no CAPT ND image:
- replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(a) If the fault continues:
- do a check of the wiring from the CAPT ND (3WT1) to the DMC1 (1WT1): . pins AA/21, 22 to pins AB/9B, 9C . pins AA/23,24 to pins AB/9D, 9E (Ref. ASM 31-61/04).
1 If there is no continuity:
_ - repair the wiring.
2 If there is continuity:
_
- do a check and repair the wiring from the DMC1 (1WT1) to the DMC3 (1WT3): . pins AB/9H, 9J to pins AB/10B, 10C . pins AB/9F, 9G to pins AB/10D, 10E (Ref. ASM 31-61/04).
a If the fault continues:
_
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(3) If the test gives the maintenance message DMC3 : RECONF WIRING and there is no upper ECAM DU image:
- replace the DU-ECAM, UPPER (4WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(a) If the fault continues:
- do a check of the wiring from the upper ECAM DU (4WT1) to the DMC1 (1WT1): . pins AA/35, 36 to pins AB/11B, 11C . pins AA/38, 39 to pins AB/11D, 11E (Ref. ASM 31-61/04).
1 If there is no continuity:
_ - repair the wiring.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-63-81∞∞∞∞∞∞∞∞∞∞Page 215
Feb 01/98 CES 2 If there is continuity:
_
- do a check and repair the wiring from the DMC1 (1WT1) to the DMC3 (1WT3): . pins AB/11F, 11G to pins AB/11D, 11E . pins AB/11H, 11J to pins AB/11B, 11C (Ref. ASM 31-61/04).
a If the fault continues:
_
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3
