Loss of the CAPT PFD
1. Possible Causes
_______________
- PFD-CAPT (2WT1)
- DMC-3 (1WT3)
- DMC-1 (1WT1)
- wiring
- C/B-EIS/PFD/CAPT (11WT1)
- POT-PFD, CAPT (7WT1)
- C/B-EIS/PFD/CAPT/SWTG (22WT1)
- RELAY-BUS 1 TO ESS BUS SWTG, DMC3 (26WT)
- C/B-EIS/DMC3/STBY/SPLY (14WT1)
- C/B-EIS/DMC3/SWTG (21WT3)
- SEL SW-EIS DMC (18WT)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
IPC 316808 AMM 31-60-00-860-001 EIS Start Procedure AMM 31-60-00-860-002 EIS Stop Procedure AMM 31-63-22-000-001 Removal of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2) AMM 31-63-22-400-001 Installation of the Display Unit
(2WT1,2WT2,3WT1,3WT2,4WT1,4WT2) AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3) AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3) ASM 31-61/02 ASM 31-68/01 ASM 31-68/02
3. Fault Confirmation
__________________
A. Job Set-up Do the EIS start procedure (CAPT PFD only) (Ref. AMM TASK 31-60-00-860-001).
B. Test
Make sure that the CAPT PFD stays off.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 205
201-299, 301-399, Aug 01/05 CES
4. Fault Isolation
_______________
A. If the CAPT PFD stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at NORM:
(1) Do a check for 115VAC at pin AA/104 of the CAPT PFD (2WT1) (Ref. ASM 31-61/02).
(a) If there is 115VAC:
- replace the PFD-CAPT (2WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(b) If there is no 115VAC:
- do a check for a ground signal at pin AA/102 of the CAPT PFD (2WT1).
1_ If there is no ground signal:
- repair the wiring from CAPT PFD (2WT1) pin AA/102 to the
ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from CAPT PFD (2WT1) pin AA/104 to the circuit breaker (11WT1).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_ - replace the C/B-EIS/PFD/CAPT (11WT1).
(2) If the fault continues:
- do a check of the wiring from CAPT PFD (2WT1) pins AA/49, 50, 51 to CAPT PFD potentiometer (7WT1) pins A/1, 2, 3 (Ref. ASM 31-68/01).
(a) If there is continuity:
- replace the PFD-CAPT (2WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
1 If the fault continues:
_
- replace the POT-PFD, CAPT (7WT1) (Ref. IPC 316808).
(b) If there is no continuity:
- repair the wiring from CAPT PFD (2WT1) pins AA/49, 50, 51 to CAPT PFD potentiometer (7WT1) pins A/1, 2, 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 206
201-299, 301-399, Aug 01/05 CES
B. If the CAPT PFD stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at CAPT/3:
(1) Do a check for 28VDC at pin AA/93 of the CAPT PFD (2WT1) (Ref. ASM 31-61/02).
(a) If there is 28VDC:
- replace the PFD-CAPT (2WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(b) If there is no 28VDC:
- do a check for a ground signal at pin AA/106 of the CAPT PFD (2WT1).
1 If there is no ground signal:
_
- repair the wiring from CAPT PFD (2WT1) pin AA/106 to the ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from CAPT PFD (2WT1) pin AA/93 to the circuit breaker (22WT1).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_ - replace the C/B-EIS/PFD/CAPT/SWTG (22WT1).
(2) If the fault continues:
- do a check for 115VAC at pin AC/2 of the DMC3 (1WT3) (Ref. ASM 31-61/02).
(a) If there is 115VAC:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(b) If there is no 115VAC: 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3(100)
