- do a check for a ground signal at pin AC/7 of the DMC3 (1WT3).
1 If there is no ground signal:
_
- repair the wiring from DMC3 (1WT3) pin AC/7 to the ground terminal.
2 If there is a ground signal:
_ - replace the RELAY-BUS 1 TO ESS BUS SWTG, DMC3 (26WT).
a If the fault continues:
_
- replace the C/B-EIS/DMC3/STBY/SPLY (14WT1). . If the fault continues:
* do a check of the wiring from the DMC3 BUS1 TO ESS BUS SWTG relay (26WT):
- pin A2 to DMC3 (1WT3) pin AC/2
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 207
201-299, 301-399, Aug 01/05 CES
- pin A1 to the EIS/DMC3/STBY/SPLY circuit breaker (14WT1)
- pin X2 to the BUS 1XP CTL relay (20XN1)
* repair the wiring which has no continuity.
(3) If the fault continues:
- do a check for 28VDC at pin AC/3 of the DMC3 (1WT3) (Ref. ASM 31-61/02).
(a) If there is 28VDC:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(b) If there is no 28VDC:
- do a check for a ground signal at pin AC/11 of the DMC3 (1WT3) (Ref. ASM 31-61/02).
1 If there is no ground signal:
_
- repair the wiring from DMC3 (1WT3) pin AC/11 to the ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from DMC3 (1WT3) pin AC/3 to the circuit breaker (21WT3) (Ref. ASM 31-61/02).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_
- replace the C/B-EIS/DMC3/SWTG (21WT3).
(4) If the fault continues:
- do a check for a ground signal at pin AB/8H, 4C of the DMC1 (1WT1).
(a) If there is no ground signal:
- do a check for a ground signal at pin AA/2 of the EIS DMC selector switch (18WT) (Ref. ASM 31-68/02).
1 If there is no ground signal:
_ - replace the SEL SW-EIS DMC (18WT).
2 If there is a ground signal:
_
- do a check of the wiring from EIS DMC selector switch (18WT) pin 2 to DMC1 (1WT1) pin AB/8H, 4C.
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_
- replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001)..
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 208
201-299, 301-399, Aug 01/05 CES (b) If there is a ground signal:
- do a check for a ground signal at pin AB/4C of the DMC3 (1WT3) (Ref. ASM 31-68/02).
1 If there is no ground signal:
_
- do a check of the wiring from DMC3 (1WT3) pin AB/4C to the first terminal block (Ref. ASM 31-68/02).
a If there is no continuity:
_
- repair the wiring.
b If there is continuity:
_
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
C. Do the EIS start procedure (CAPT PFD only) (Ref. AMM TASK 31-60-00-860-001) and make sure that the CAPT PFD comes on.
5. Close-up
________
A. Do the EIS stop procedure (Ref. AMM TASK 31-60-00-860-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 209
201-299, 301-399, Aug 01/05 CES
Loss of the CAPT ND
1. Possible Causes
_______________
- ND-CAPT (3WT1)
- DMC-3 (1WT3)
- DMC-1 (1WT1)
- wiring
- C/B-EIS/ND/CAPT (12WT1)
- POT-ND, CAPT (8WT1)
- C/B-EIS/ND/CAPT/SWTG (23WT1)
- RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT)
- C/B-EIS/DMC3/STBY/SPLY (14WT1)
- C/B-EIS/DMC3/SWTG (21WT3)
- SEL SW-EIS DMC (18WT)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
IPC 316808 AMM 31-60-00-860-001 EIS Start Procedure AMM 31-60-00-860-002 EIS Stop Procedure AMM 31-63-22-000-001 Removal of the Display Unit
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3(101)
