「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 210
201-299, 301-399, Aug 01/05 CES
4. Fault Isolation
_______________
A. If the CAPT ND stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at NORM:
(1) Do a check for 115VAC at pin AA/104 of the CAPT ND (3WT1) (Ref. ASM 31-61/02).
(a) If there is 115VAC:
- replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(b) If there is no 115VAC:
- do a check for a ground signal at pin AA/102 of the CAPT ND (3WT1).
1_ If there is no ground signal:
- repair the wiring from CAPT ND (3WT1) pin AA/102 to the
ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from CAPT ND (3WT1) pin AA/104 to the circuit breaker (12WT1).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_ - replace the C/B-EIS/ND/CAPT (12WT1).
(2) If the fault continues:
- do a check of the wiring from CAPT ND (3WT1) pins AA/49, 50, 51, 52 to CAPT ND potentiometer (8WT1) pins A/2, 4, 5, 6 (Ref. ASM 31-68/01).
(a) If there is continuity:
- replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
1 If the fault continues:
_
- replace the POT-ND, CAPT (8WT1) (Ref. IPC 316808).
(b) If there is no continuity:
- repair the wiring from CAPT ND (3WT1) pins AA/49, 50, 51, 52 to CAPT ND potentiometer (8WT1) pins A/2, 4, 5, 6.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 211
201-299, 301-399, Aug 01/05 CES
B. If the CAPT ND stays off and if the EIS DMC selector switch (18WT) on the SWITCHING panel 8VU is at CAPT/3:
(1) Do a check for 28VDC at pin AA/93 on the CAPT ND (3WT1) (Ref. ASM 31-61/02).
(a) If there is 28VDC:
- replace the ND-CAPT (3WT1) (Ref. AMM TASK 31-63-22-000-001) and (Ref. AMM TASK 31-63-22-400-001).
(b) If there is no 28VDC:
- do a check for a ground signal at pin AA/106 of the CAPT ND (3WT1).
1 If there is no ground signal:
_
- repair the wiring from CAPT ND (3WT1) pin AA/106 to the ground terminal.
2 If there is a ground signal:
_
- do a check of the wiring from CAPT ND (3WT1) pin AA/93 to the circuit breaker (23WT1).
a If there is no continuity:
_ - repair the wiring.
b If there is continuity:
_ - replace the C/B-EIS/ND/CAPT/SWTG (23WT1)
(2) If the fault continues:
- do a check for 115VAC at pin AC/2 of the DMC3 (1WT3) (Ref. ASM 31-61/02).
(a) If there is 115VAC:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(b) If there is no 115VAC:
- do a check for a ground signal at pin AC/7 of the DMC3 (1WT3).
1 If there is no ground signal:
_
- repair the wiring from DMC3 (1WT3) pin AC/7 to the ground terminal.
2 If there is a ground signal:
_ - replace the RELAY-BUS1 TO ESS BUS SWTG, DMC3 (26WT).
a If the fault continues:
_
- replace the C/B-EIS/DMC3/STBY/SPLY (14WT1) . If the fault continues:
* do a check of the wiring from the DMC3 BUS1 TO ESS BUS SWTG relay (26WT): . pin A2 to DMC3 (1WT3) pin AC/2
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞31-63-82∞∞∞∞∞∞∞∞∞∞Page 212
201-299, 301-399, Aug 01/05 CES . pin A1 t the EIS/DMC3/STBY/SPLY circuit breaker (14WT1) . pin X2 to the BUS 1XP CTL relay (20XN1)
中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 3(102)
