- replace the DFDR (1TU) (Ref. AMM TASK 31-33-55-000-001) and (Ref. AMM TASK 31-33-55-400-002).
(3) If the fault continues:
- replace the DMU/FDIU (FDIMU) (10TV) (Ref. AMM TASK 31-36-34-000-002) and (Ref. AMM TASK 31-36-34-400-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-33-00∞∞∞∞∞∞∞∞∞∞Page 217
Aug 01/05 CES
B. Do the test given in paragraph 3.A. again to check the correct operation (no maintenance message display).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-33-00∞∞∞∞∞∞∞∞∞∞Page 218
Aug 01/04R
CES No AC Ident
1. Possible Causes
_______________
- FDIU (2TU)
- DMU/FDIU (FDIMU) (10TV)
- Pin Program
- Coding Plug 197VC-A
- wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 31-33-34-000-001 Removal of the Flight Data Interface Unit (FDIU) (2TU) AMM 31-33-34-400-001 Installation of the Flight Data Interface Unit (FDIU)
(2TU)
AMM 31-36-34-000-002 Removal of the FDIU/DMU (FDIMU) (10TV)
AMM 31-36-34-400-002 Installation of the FDIU/DMU (FDIMU) (10TV)
ASM 31-34/00
ASM 31-34/03
3. Fault Confirmation
__________________
A. Get a printout of the last leg report. Make sure that the correct aircraft identification is shown at the top of the printout.
4. Fault Isolation
_______________
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
A. If the aircraft identification is not correct or not shown:
- do a check and adjust the Pin Program from the Coding Plug 197VC-A (Ref. ASM 31-34/03) if necessary.
(1) If the fault continues :
- do a check and repair the wiring between Coding Plug 197VC-A connector and the FDIU (1TU) (Ref. ASM 31-34/00) if necessary.
(2) If the fault continues :
- replace the FDIU (2TU), (Ref. AMM TASK 31-33-34-000-001) (Ref. AMM TASK 31-33-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-33-00∞∞∞∞∞∞∞∞∞∞Page 219
May 01/05 CESR **ON A/C 106-149, 211-299, 301-399, 401-499,
A. If the aircraft identification is not correct or not shown:
- do a check and adjust the Pin Program from the Coding Plug 197VC-A (Ref. ASM 31-34/03) if necessary.
(1) If the fault continues :
- do a check and repair the wiring between Coding Plug 197VC-A connector and the FDIMU (10TV) (Ref. ASM 31-34/00) if necessary.
(2) If the fault continues :
- replace the DMU/FDIU (FDIMU) (10TV), (Ref. AMM TASK 31-36-34-000-002) (Ref. AMM TASK 31-36-34-400-002).
**ON A/C ALL
B. Get a printout of the last leg report again. The correct aircraft identification is shown at the top of the printout (no maintenance message is displayed).
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-210,
TASK 31-33-00-810-823
DMU receives no Data from the FDIU (2TU)
1. Possible Causes
_______________
- DMU (1TV)
- FDIU (2TU)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 1(65)
