(b) from the Clock (2FS) connector A/E, F to the MMR1 (40RT1) connector AB/9E, 9H.

 **ON A/C ALL
 B. Do the test given in Para. 3.B.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-21-00∞∞∞∞∞∞∞∞∞∞Page 208
 Aug 01/05 CES

 TASK 31-21-00-810-805
 Loss of the Bus Output from the Clock

 1. Possible Causes
_______________
 - CLOCK (2FS)

 - wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 31-21-21-000-001 Removal of the Clock (2FS)
 AMM 31-21-21-400-001 Installation of the Clock (2FS)
 AMM 31-32-00-740-003 Ground Scanning of the CFDIU
 ASM 31-21/01

 3. Fault Confirmation
__________________
 A. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU CLOCK/NORM/SPLY 6FS F11
 B. Test Do the ground scanning of the CFDIU (Ref. AMM TASK 31-32-00-740-003).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message AFS:CLOCK:
 - replace the CLOCK (2FS), (Ref. AMM TASK 31-21-21-000-001) and (Ref. AMM TASK 31-21-21-400-001).
 (1) If the fault continues:
 - do a check and repair the wiring from the clock (2FS) pins A/W, X to the first terminal block , (Ref. ASM 31-21/01).
 B. Do the test given in Para. 3.B.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-21-00∞∞∞∞∞∞∞∞∞∞Page 209
 Feb 01/00R CES

 Loss of the GMT Indication on the Lower ECAM DU
 1. Possible Causes
_______________
 - CFDIU (1TW) R - wiring
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 31-21-00-750-002 Procedure to set the Clock
 AMM 31-32-34-000-001 Removal of the CFDIU (1TW)
 AMM 31-32-34-400-001 Installation of the CFDIU (1TW)

R ASM 31-32/03
 3. Fault Confirmation
__________________
 A. Table of the circuit breakers used in this procedure:
 -------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
 -------------------------------------------------------------------------------
121VU CFDS/CFDIU/SPLY 2TW J18
 B. Do the clock setting (Ref. AMM TASK 31-21-00-750-002).
 4. Fault Isolation
_______________
 A. If the fault symptom is identified by GMT indication in amber crosses on the lower ECAM DU:
 - open the circuit breaker 2TW.
 - close the circuit breaker 2TW.
 (1) If the circuit breaker trips:

 - replace the CFDIU (1TW) (Ref. AMM TASK 31-32-34-000-001) and (Ref. AMM TASK 31-32-34-400-001).

 (2) If the fault continues

 - replace the CFDIU (1TW) (Ref. AMM TASK 31-32-34-000-001) and (Ref. AMM TASK 31-32-34-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-21-00∞∞∞∞∞∞∞∞∞∞Page 210
 Feb 01/03 CES

R  B. If the Log book mentions the loss of expected time at waypoint on the ND: 
R  - replace the CFDIU (1TW) and (Ref. AMM TASK 31-32-34-000-001). (Ref. AMM 
R  TASK 31-32-34-400-001) 
R  (1) If the fault continues: 
R  (a) For a DMC2 related fault (fault on the first officer side) 
R  - do a check and repair the wiring between the CFDIU (1TW) and 
R  the DMC 2 (1WT2) from pins AB/2H, 2J to pins AA/15D, 15E (Ref. 
R  ASM 31-32/03). 
R  (b) For a DMC1 related fault (fault on the captain side) 
R  - do a check and repair the wiring between the CFDIU (1TW) and 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 指示和記錄系統 1(3)