3. Fault Confirmation
__________________
A. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU ELEC/EXT PWR/CTL 11XG X29 122VU ELEC/GPCU 7XG Y24 123VU GND/PWR/PROT 2XG AB07
B. On the CFDS MENU page, get access to the class 3 faults reading page (Ref. AMM TASK 31-32-00-869-002).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-105, 151-199, ∞∞31-32-00∞∞∞∞∞∞∞∞∞∞Page 207
201-228, 301-302, May 01/05 CES
4. Fault Isolation
_______________
A. If the test gives the maintenance message NO GPCU DATA:
- replace the CFDIU (1TW), (Ref. AMM TASK 31-32-34-000-001) and (Ref. AMM TASK 31-32-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring from the CFDIU (1TW) pins AA/6F, 6G to the GPCU (1XG) pins AA/7D, 7C, (Ref. ASM 31-32/06).
(2) If the fault continues:
- do a check for 28VDC at GPCU (1XG) pin AB/15A (Ref. ASM 24-41/00).
(a) if there is 28VDC:
- replace the GPCU (1XG), (Ref. AMM TASK 24-41-34-000-001) and (Ref. AMM TASK 24-41-34-400-001).
(b) if there is no 28VDC:
- do a check for open or short to ground of the wiring between the C/B-ELEC/GPCU (7XG) and the GPCU (1XG) pin AB/15A.
1_ if there is an open or a short to ground:
- repair the defective wiring(s).
2_ if there is no open or short to ground:
- replace the defective C/B-ELEC/GPCU (7XG).
B. Do the test given in Para. 3.B.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-105, 151-199, ∞∞31-32-00∞∞∞∞∞∞∞∞∞∞Page 208
201-228, 301-302, May 01/05 CES
R **ON A/C ALL
TASK 31-32-00-810-813
Loss of the Output Bus from the SDCU or the CIDS Director(s) to the CFDIU
1. Possible Causes
_______________
- CFDIU (1TW)
- SDCU (10WQ)
- wiring from the CFDIU (1TW) to the SDCU (10WQ)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 26-17-34-000-001 Removal of the Smoke-Detection Control Unit (SDCU) (10WQ) AMM 26-17-34-400-001 Installation of the Smoke-Detection Control Unit
(SDCU) (10WQ)
AMM 31-32-00-740-009 Read the AVIONICS STATUS on the MCDU
AMM 31-32-34-000-001 Removal of the CFDIU (1TW)
AMM 31-32-34-400-001 Installation of the CFDIU (1TW)
ASM 31-32/04
3. Fault Confirmation
__________________
A. Read the AVIONICS STATUS on the MCDU (Ref. AMM TASK 31-32-00-740-009).
4. Fault Isolation
_______________
A. If the test gives the maintenance message NO SDCU DATA:
- replace the CFDIU (1TW), (Ref. AMM TASK 31-32-34-000-001) and (Ref. AMM TASK 31-32-34-400-001).
(1) If the fault continues:
- replace the SDCU (10WQ) (Ref. AMM TASK 26-17-34-000-001) and (Ref. AMM TASK 26-17-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring from the CFDIU (1TW) to the SDCU (10WQ) from pins AA/11H,11J to pins AB/3C, 4C , (Ref. ASM 31-32/04).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞31-32-00∞∞∞∞∞∞∞∞∞∞Page 209
Feb 01/05 CES
INTENTIONALLY BLANK
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R ∞∞31-32-00∞∞∞∞∞∞∞∞∞∞Page 210
Loss of the Bus Output from the FDU of the Engine 1 to the CFDIU
1. Possible Causes
_______________
R
- FDU-ENG1 (2WD1) R - CFDIU (1TW)
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 指示和記錄系統(tǒng) 1(6)
