- if the wiring is not correct, repair the above wiring.

 12 Do a check of the wiring of the DSI 17 signal from the ELAC2
__ (2CE2) COM part to the MON part (Ref. ASM 27-92/44).
 - if the wiring is correct, see Para. 13_.

 - if the wiring is not correct, repair the above wiring.

 13 Do a check of the wiring of the PIN PROGRAM ELAC2 signal from
__ the ELAC2 (2CE2) COM part and MON part to the ground terminal (Ref. ASM 27-92/40).
 14 Replace the SSTU-ROLL CTL, CAPT (4CE1) and SSTU-ROLL CTL, F/O
__ (4CE2) (Ref. AMM TASK 27-92-41-000-002) and (Ref. AMM TASK 27-92-41-400-002).
 (d) If the fault continues:
 1 Do a check of the wiring of the PWR SPLY + 28VDC signal from
_ the ELAC2 (2CE2) COM part and MON part to the first terminal block (Ref. ASM 27-92/02).
 - if there is continuity, see Para. 2_.

 - if there is no continuity repair the above wiring.

 2 Do a check of the wiring of the PWR SPLY GND signal from the
_ ELAC2 (2CE2) COM part and MON part to the ground terminal (Ref. ASM 27-92/02).
 - if there is continuity, see Para. 3_.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-099, 101-149, 151-199, ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page B222

 - if there is no continuity, repair the above wiring.
 3 Do a check of the wiring of the CTL + 28VDC and ELAC2 ENGAGED
_ (DSI 50) signals from the ELAC2 (2CE2) COM part and MON part to the pushbutton switch (6CE2) (Ref. ASM 27-92/02).
 - if there is continuity, see Para. 4_.

 - if there is no continuity, repair the above wiring.

 4 Do a check of the wiring from the pushbutton switch (6CE2) pin
_ A/C3 to the first terminal block (Ref. ASM 27-92/02).
 - if there is continuity, see Para. 5_.

 - if there is no continuity, repair the above wiring.

 5 Replace the P/BSW-FLT CTL/ELAC 2 (6CE2) (Ref. IPC 27920802).
_
R **ON A/C 301-399,

R A. If the test confirms the fault:
R - Do the operational test of the ELACs (Ref. AMM TASK 27-93-00-710-001)
R to make sure that the ELAC 2 servoes its associated surfaces.

R (1) If the flight controls move according to the ELAC 2 servoing:

R (a) Remove the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-000-001).

R (b) At the ELAC 2 receptacle, do a check of the resistance between
R pin AB/11J and pin AE/14C (Ref. ASM 27-92/03).

R 1_ If the resistance is less than 280 ohms:

R a_ Remove the RELAY-ELAC 2 ANN SPLY (40CE2) (Ref. IPC
R 27920803).

R b_ Do a check of the resistance of the relay between pin X1
R and pin X2.
R - If the resistance is less than 280 ohms:

R . replace the RELAY-ELAC 2 ANN SPLY (40CE2) (Ref. IPC
R 27920803)

R . replace the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-400-R 001).
R - If the resistance is between 280 and 400 ohms:

R . do a check and repair the wiring of the RLY ELAC FAULT
R signal from the relay to the ELAC 2 (Ref. ASM 27-92/03)

R . install the relay

R . replace the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-400-R 001).

R 2_ If the resistance is more than 400 ohms:
R a_Remove the relay 40CE2.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page B223
 May 01/04 CES

R  b Do a check of the resistance of the relay between pins X1_ 
R  and X2. 
R  - If the resistance is more than 400 ohms: 
R  . replace the RELAY-ELAC 2 ANN SPLY (40CE2) (Ref. IPC 
R  27920803) 
R  . install the ELAC 2 (Ref. AMM TASK 27-93-34-400-001). 
R  - If the resistance is between 280 and 400 ohms: 
R  . do a check and repair the wiring of the RLY ELAC FAULT 
R  signal from the relay to the ELAC 2. (Ref. ASM 27-92/03) 
R  . install the relay 
R  . install the ELAC 2 (Ref. AMM TASK 27-93-34-400-001). 
R  3_  If the resistance is between 280 and 400 ohms:
R  a Remove the FCDC-1 (3CE1) (Ref. AMM TASK 27-95-34-000-001)._ 
R  - if the warning ELAC2 stays: 
R  . install the FCDC-1 (3CE1) (Ref. AMM TASK 27-95-34-400-
R  001). 
R  . continue the trouble shooting at Para. b_. 
R  - if the warning ELAC2 goes off, replace the FCDC-2 (3CE2) 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(64)