(Activation for the BITE Test)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-93/08
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the side stick assembly (activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).
(2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
(a) If the ground scanning gives the maintenance message: ELAC2 OR WIRING FROM R Y ELEV MODE XDCR 34CE4
- refer to Para. Fault Isolation.
(b) If the ground scanning gives at least two maintenance messages of the two lists below: First list:
- ELAC2 COM OR INPUT OF THS ACTR XDCR1 9CE
- ELAC2 OR WIRING FROM L G ELEV POS XDCR 34CE1
- ELAC2 OR WIRING FROM R Y ELEV POS XDCR 34CE2 Second list:
- ELAC2 MON OR INPUT OF THS ACTR XDCR1 9CE
- ELAC2 OR WIRING FROM L ELEV POS MON XDCR
- ELAC2 OR WIRING FROM R ELEV POS MON XDCR
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A259
Feb 01/03R CES
- ELAC2 OR WIRING FROM L B ELEV MODE XDCR 34CE3
- ELAC2 OR WIRING FROM R Y ELEV MODE XDCR 34CE4
1_ First case:
Combination of maintenance messages of the first list, do this
trouble shooting procedure (Ref. TASK 27-90-00-810-814).
2_ Second case:
Combination of maintenance messages of the second list, do
this trouble shooting procedure (Ref. TASK 27-90-00-810-815).
3_ Third case:
Combination of maintenance messages of the first and second
lists, do this trouble shooting procedure (Ref. TASK 27-90-00-
810-816).
4. Fault Isolation
_______________
A. If the test gives the maintenance message: ELAC2 OR WIRING FROM R B ELEV MODE XDCR 34CE4
- replace the ELAC-2 (2CE2) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).
(1) If the fault continues:
- do a check and repair the wiring of the MODE XDCR (ANI 7-2) signal from the ELAC 2 (2CE2) MON part to the first terminal block (Ref. ASM 27-93/08).
B. Do the tests given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A260
Feb 01/03R
CES Failure of the Right Blue Elevator Servocontrol Actuator Solenoid Valve
CAUTION : DO NOT SWAP FLIGHT CONTROL COMPUTERS. IF THERE IS A SHORT CIRCUIT,
_______ YOU WILL CAUSE DAMAGE TO A SERVICEABLE COMPUTER WHEN YOU SWAP THEM.
1. Possible Causes
_______________
- RELAY-THS MOT 3 INHIBITION 1 (51CE)
- RELAY-THS MOT 3 INHIBITION 2 (52CE)
- ELAC-2 (2CE2)
- SERVO CTL-R ELEVATOR, OUTBD B (34CE4)
- solenoid valve of the servocontrol 34CE4
- wiring of the SOL VLV1 signal from the servocontrol (34CE4) to the ELAC2 (2CE2)
- wiring from the ELAC2 (2CE2) COM part to the ELAC2 COM part
- wiring from the ELAC2 (2CE2) COM part to the ELAC2 MON part
- wiring from the ELAC2 (2CE2) MON part pins AE/13B and AE/12C to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
IPC 27920803
AMM 27-34-51-000-001 Removal of the Elevator Servo Control
AMM 27-34-51-000-005 Removal of the Elevator Servo Control Actuator
Solenoid Valve
AMM 27-34-51-400-001 Installation of the Elevator Servo Control
AMM 27-34-51-400-004 Installation of the Elevator Servo Control Actuator
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(40)
