- ELAC-1 (2CE1)

 - solenoid valve of the servocontrol 34CE2

 - wiring of the SOL VLV1 signal from the servocontrol (34CE2) to the ELAC1 (2CE1)

 - wiring from the ELAC1 (2CE1) COM part to the ELAC1 COM part

 - wiring from the ELAC1 (2CE1) COM part to the ELAC1 MON part

 - wiring from the ELAC1 (2CE1) MON part pins AE/13B and AE/12C to the first terminal block

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 27-34-51-000-001 Removal of the Elevator Servo Control
 AMM 27-34-51-000-005 Removal of the Elevator Servo Control Actuator
 Solenoid Valve
 AMM 27-34-51-400-001 Installation of the Elevator Servo Control
 AMM 27-34-51-400-004 Installation of the Elevator Servo Control Actuator
 Solenoid Valve
 AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
 AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
 AMM 27-96-00-710-020 Operational Test of the Side Stick Assembly
 (Activation for the BITE Test)
 AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
 ASM 27-93/07
 3. Fault Confirmation
__________________
 A. Test
 (1) Do the operational test of the side stick assembly (Activation for the BITE test) (Ref. AMM TASK 27-96-00-710-020).
 NOTE : Before you start the operational test procedure, release the
____ FLT CTL/ELAC2 pushbutton switch (on this pushbutton switch, the OFF legend comes on).
 Feb 01/03R CES

 (2) Do the BITE test of the EFCS (Ground Scanning) (Ref. AMM TASK 27-96-00-740-001).
 4. Fault Isolation
_______________
 A. If the tests give the maintenance message R Y ELEV MODE VLV 34CE2:
 (1) Remove the ELAC1 (Ref. AMM TASK 27-93-34-000-001).

 (2) At the ELAC1 receptacle, do a check of the resistance between the pin AB/14K and the pin AE/14B (Ref. ASM 27-93/07).

 NOTE : The resistance must be between 40 and 100 Ohms.
____
 (a) If the resistance is less than 40 Ohms:
 - at the inboard elevator servocontrol (34CE2), do a check of the resistance of the solenoid valve between the pin C/K and the pin C/L (Ref. ASM 27-93/07).
 NOTE : The resistance must be between 40 and 100 Ohms.
____
 1 If the resistance values are out of the specified limits:
_ a Replace the solenoid valve of the servocontrol 34CE2 (Ref.
_ AMM TASK 27-34-51-000-005) and (Ref. AMM TASK 27-34-51-400-004).
 b Do again a check of the resistance of the solenoid valve
_ between the pin C/K and the pin C/L of the inboard elevator servocontrol (34CE2) (40 to 100 Ohms).
 - If the resistance values are out of the specified limits: . Replace the SERVO CTL-R ELEVATOR, INBD Y (34CE2) (Ref. AMM TASK 27-34-51-000-001) and (Ref. AMM TASK 27-34-51-400-001). . Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).

 - If the resistance values are in the specified limits: Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).

 2 If the resistance values are in the specified limits:
_
 a Repair the wiring of the SOL VLV1 signal from the
_ servocontrol (34CE2) to the ELAC1 (2CE1), from the pin C/K to the pin AB/14K and from the pin C/L to the pin AE/14B (Ref. ASM 27-93/07):
 b Replace the ELAC-1 (2CE1) (Ref. AMM TASK 27-93-34-000-001)
_ and (Ref. AMM TASK 27-93-34-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page A278
 Feb 01/03R
 CES

 (b) If the resistance is more than 100 Ohms:
 - at the inboard elevator servocontrol (34CE2), do a check of the resistance of the solenoid valve between the pin C/K and the pin C/L (Ref. ASM 27-93/07).
 NOTE : The resistance must be between 40 and 100 Ohms.
____
 1 If the resistance values are out of the specified limits:
_
 a Replace the solenoid valve of the servocontrol 34CE2 (Ref.
_ AMM TASK 27-34-51-000-005) and (Ref. AMM TASK 27-34-51-400-004).
 b Do again a check of the resistance of the solenoid valve
_ between the pin C/K and the pin C/L of the inboard elevator servocontrol (34CE2) (40 to 100 Ohms).
 - If the resistance values are out of the specified limits: . Replace the SERVO CTL-R ELEVATOR, INBD Y (34CE2) (Ref. AMM TASK 27-34-51-000-001) and (Ref. AMM TASK 27-34-51-400-001). . Install the ELAC1 (Ref. AMM TASK 27-93-34-400-001).
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(47)