(Ref. ASM 27-93/12).
B. Do the tests given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page 287
May 01/99R
CES Incorrect Position of the THS for the ELAC 1
1. Possible Causes
_______________
- ELAC-1 (2CE1)
- electronic module N.2 of the picth trim actuator
- monitor position transducer of the THS actuator R - command position transducer of the THS actuator
- RLY-PITCH TRIM ACTR MOT 2 SPLY (36CE2)
- wiring from the relay (36CE2) pin A/X2 to the ground
- wiring from the relay (36CE2) to the ELAC 1 (2CE1)
- wiring from the relay (36CE2) to the SEC 1 (1CE1)
- wiring from the THS actuator (9CE) pin B/M to the ground
- wiring from the relay (36CE2) to the THS actuator (9CE)
- wiring from the relay (36CE2) A/A2 to the C/B (19CE2)
- wiring from the XDCR MON MOT 2 (V1, V2) signal R - wiring from the XDCR COM MOT 2 (V1, V2) signal
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
IPC 27920803 AMM 27-44-56-000-001 Removal of the Position Transducer from the THS Actuator 9CE AMM 27-44-56-400-001 Installation of the Position Transducer to the THS Actuator 9CE AMM 27-44-57-000-002 Removal of the Electronic Modules of the Pitch Trim Actuator AMM 27-44-57-400-002 Installation of the Electronic Modules of the Pitch
Trim Actuator
AMM 27-93-34-000-001 Removal of the ELAC (2CE1,2CE2)
AMM 27-93-34-400-001 Installation of the ELAC (2CE1,2CE2)
AMM 27-96-00-710-022 Operational Test of the THS Actuator Electrical
Control (Activation for BITE Test)
AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning)
ASM 27-93/12
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the THS actuator electrical control (Ref. AMM TASK 27-96-00-710-022).
NOTE : Do the ground setting only with the ELAC 1.
____
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-93-00∞∞∞∞∞∞∞∞∞∞Page 288
May 01/01 CES
(2) Do the BITE test of the EFCS (ground scanning) (Ref. AMM TASK 27-96-00-740-001).
4. Fault Isolation
_______________
A. If the BITE test gives the maintenance message:
THS ACTR POS ERROR 9CE OF ELAC1
- replace the ELAC-1 (2CE1), (Ref. AMM TASK 27-93-34-000-001) and (Ref. AMM TASK 27-93-34-400-001).
(1) If the fault continues:
- replace the electronic module N.2 of the picth trim actuator, (Ref. AMM TASK 27-44-57-000-002) and (Ref. AMM TASK 27-44-57-400-002).
(2) If the fault continues:
- replace the monitor position transducer of the THS actuator, (Ref. AMM TASK 27-44-56-000-001) and (Ref. AMM TASK 27-44-56-400-001).
R (3) If the fault continues:
R - replace the command position transducer of the THS actuator, (Ref.
R AMM TASK 27-44-56-000-001) and (Ref. AMM TASK 27-44-56-400-001).
R (4) If the fault continues :
- replace the RLY-PITCH TRIM ACTR MOT 2 SPLY (36CE2) (Ref. IPC 27920803)
R (5) If the fault continues :
- do a check of the wiring from the relay (36CE2) pin A/X2 to the ground (Ref. ASM 27-93/12).
- do a check of the wiring from the relay (36CE2) to the ELAC 1 (2CE1), from the pin A/X1 to the pin AD/15J (Ref. ASM 27-93/12).
- do a check of the wiring from the relay (36CE2) to the SEC 1 (1CE1), from the pin A/X1 to the pin AE/13E (Ref. ASM 27-93/12).
(a) If there is no continuity, repair the wiring.
(b) If there is continuity :
- do a check of the wiring from the THS actuator (9CE) pin B/M to the ground, (Ref. ASM 27-93/12).
- do a check of the wiring from the relay (36CE2) to the THS actuator (9CE) from the pin A/A1 to the pin B/K (Ref. ASM 27-93/12). 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 3(15)
