Slats - SFCC 1 (2) Gives PCU Valveblock 25CV (26CV) Valve Sensor Message
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 - THE FLIGHT CONTROLS

 - THE FLIGHT CONTROL SURFACES

 - THE LANDING GEAR AND THE RELATED DOORS

 - COMPONENTS THAT MOVE.

 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Possible Causes
_______________
 - SFCC-1 (21CV)

 - SFCC-2 (22CV)

 - VALVE BLOCK SLAT 1 (25CV)

 - VALVE BLOCK SLAT 2 (26CV)

 - valve sensor

 - aircraft wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV)
 AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
 AMM 27-84-53-000-001 Removal of the Valve Blocks 25CV, 26CV of the Power

 Control Unit (Slat) AMM 27-84-53-400-001 Installation of the Valve Blocks 25CV, 26CV of the Power Control Unit (Slat) AMM 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST
 F/CTL Page
 ASM 27-81/02
 ASM 27-81/03

 3. Fault Confirmation
__________________
 A. Test
 (1) At the MCDU, access the SYSTEM REPORT / TEST page and select F/CTL> (Ref. AMM TASK 31-32-00-860-006).

 (2) Select <SFCCX (where X is the No. of the applicable SFCC).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-81-00∞∞∞∞∞∞∞∞∞∞Page 279
 May 01/05R CES

 (3) Select <SFCC/TEST, to do the SFCC BITE test:
 - if the fault message SLT1 (2) PCU VALVEBLOCK 25CV (26CV) VALVE SENSOR 27-84-53 is shown, do the Fault Isolation Procedure given in Para. 4.
 NOTE : This message is not a CFDS Normal Mode message and is only
____
 shown in SFCC reports.

 4. Fault Isolation
_______________
 A. Procedure
 (1) Interchange the SFCC1 and SFCC2 (Ref. AMM TASK 27-51-34-000-001) and (Ref. AMM TASK 27-51-34-400-001).

 (2) Do the test given in Para. 3.A:

 (a) If the fault goes, replace the initial SFCC-1 (21CV) or SFCC-2 (22CV), (Ref. AMM TASK 27-51-34-000-001) and (Ref. AMM TASK 27-51-34-400-001).

 (b) If the fault continues, replace the applicable VALVE BLOCK SLAT 1 (25CV) or VALVE BLOCK SLAT 2 (26CV), (Ref. AMM TASK 27-84-53-000-001) and (Ref. AMM TASK 27-84-53-400-001).

 NOTE : The valve sensor is not a Line Replaceable Unit (LRU) and
____ it is necessary to replace the valve block.
 (3) If the fault continues:
 (a) Do a check of the aircraft wiring and repair as necessary (Ref. ASM 27-81/02) or (Ref. ASM 27-81/03).

 (b) Do the test given in Para. 3.A.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-81-00∞∞∞∞∞∞∞∞∞∞Page 280
 May 01/05R
 CES  Slats - SFCC TEST Gives the Message PERFORMED WITH FAULT

 1. Possible Causes
_______________
 - SFCC-1 (21CV)

 - SFCC-2 (22CV)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV) AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
 3. Fault Confirmation
__________________
 A. Test
 (1) If the SLAT SFCC TEST gives the message PERFORMED WITH FAULT, do the fault isolation procedure given in Para. 4.
 4. Fault Isolation
_______________
 A. Procedure
 (1) Replace the applicable SFCC-1 (21CV) or SFCC-2 (22CV), (Ref. AMM TASK 27-51-34-000-001) and (Ref. AMM TASK 27-51-34-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-81-00∞∞∞∞∞∞∞∞∞∞Page 281
 May 01/05R
 CES

 Slats System 1 (2) Fault with the A-LOCK Flag Shown on the EWD When Retracting the Slats While the Aircraft is on the Ground
　
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 飛行操縱 2(83)