Flap Flag Indication Does Not Agree With Flap Position
1. Possible Causes_______________
- IPPU-FLAP (3CN)
2. Job Set-up Information______________________ Not Applicable
3. Fault Confirmation__________________
A. Procedure
(1) Examine the post flight report for a CFDS fault message with the FIN 3CN A or 3CN B shown.
4. Fault Isolation_______________
A. Procedure
(1) If the FIN 3CN A or 3CN B is shown:
(a) This is an IPPU-FLAP (3CN) fault.
(b) For the trouble-shooting procedure (Ref. 27 CFDS).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 294
May 01/05R
CES Flap Menu Not Available On The CFDIU
1. Possible Causes
_______________
- SFCC-1 (21CV)
- SFCC-2 (22CV)
- RELAY-A/C ON GND (95CV)
- RELAY-A/C ON GND (97CV)
- PROX SNSR R L/G EXT 20GA
- PROX SNSR L L/G EXT 21GA
- PROX SNSR R L/G EXT 22GA
- PROX SNSR L L/G EXT 23GA
- aircraft wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 27-51-00-740-002 Bite Test of the Slat and Flap Control Computers
(Flap System)
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV)
AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
ASM 27-51/02
ASM 27-51/03
3. Fault Confirmation
__________________
A. Test
(1) Do a BITE test of the applicable SFCC (Ref. AMM TASK 27-51-00-740-002).
4. Fault Isolation
_______________
A. Procedure
(1) If the flap menu is not available:
(a) Swop the SFCC's and repeat the test in Para. 3.A. on SFCC-1 (21CV) and SFCC-2 (22CV).
(2) If the fault has moved to the other SFCC position, swop the SFCC's back and replace the SFCC that has the fault (Ref. AMM TASK 27-51-34-000-001) and (Ref. AMM TASK 27-51-34-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 295
May 01/05R CES
(3) If the fault did not move to the other SFCC position, swop the SFCC's back Ref. Para. (2).
(a) Make sure that there are no landing gear system faults (Ref. ATA 32-31-00)
NOTE : Main landing gear shock absorber proximity sensor faults
____
will cause this failure.
- For SFCC 1 PROX SNSR R L/G EXT 20GA and PROX SNSR L L/G EXT 21GA
- For SFCC 2 PROX SNSR R L/G EXT 22GA and PROX SNSR L L/G EXT 23GA
(4) If there were any landing gear faults, do the test in Para. 3.A.
(5) If the fault continues:
(a) Swop the RELAY-A/C ON GND (95CV) with RELAY-A/C ON GND (97CV).
(b) Do the test in Para. 3.A. on the SFCC 1 and SFCC 2.
(c) If the fault moves to the other system, replace the relay in the system that now has the fault.
(d) Do the test in Para. 3.A.
(6) If the fault does not move to the other system, do a check of the aircraft wiring:
- for SFCC 1 from C/B 6CV to the LGCIU 1 and from the RELAY A/C ON GND 95CV to SFCC 1 (Ref. ASM 27-51/02).
- for SFCC 2 from C/B 8CV to the LGCIU 2 and from the RELAY A/C ON GND 97CV to SFCC 2 (Ref. ASM 27-51/03).
(a) Repair any defect found.
(b) Do the test in Para. 3.A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 296
May 01/05R
CES Flaps SFCC Flap Channel Failure
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
- THE FLIGHT CONTROLS
- THE FLIGHT CONTROL SURFACES
- THE LANDING GEAR AND THE RELATED DOORS 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 飛行操縱 2(12)
