1. Possible Causes
_______________
- SFCC-1 (21CV)
- SFCC-2 (22CV)
- ADIRU-1 (1FP1)
- aircraft wiring
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 27-51-34-000-001 Removal of the SFCC (21CV,22CV)
AMM 27-51-34-400-001 Installation of the SFCC (21CV,22CV)
AMM 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST
F/CTL Page AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3) AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3) ASM 27-51/08
3. Fault Confirmation
__________________
A. Test
(1) At the ADIRU 1 CDU, set the OFF/NAV/ATT selector switch to NAV.
(2) At the MCDU, set the MENU MODE and get access to the SYSTEM REPORT/TEST F/CTL page (Ref. AMM TASK 31-32-00-860-006).
(a) Get access to the SFCC 1 (2) SYSTEM DATA FLAP page and push the line key adjacent to the ARINC 429 INPUT STATUS indication:
- if the ARINC input status shows ADIRU 1 LABEL *** NO DATA, do the Fault Isolation Procedure.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 269
May 01/04R
CES
4. Fault Isolation
_______________
A. Procedure
(1) Interchange the SFCC 1 (2) with SFCC 2 (1) (Ref. AMM TASK 27-51-34-000-001) (Ref. AMM TASK 27-51-34-400-001).
(2) Do the test given in Para. 3.A:
(a) If the fault does not continue, replace the initial SFCC-1 (21CV) (SFCC-2 (22CV)) (Ref. AMM TASK 27-51-34-000-001) and (Ref. AMM TASK 27-51-34-400-001).
(b) If the fault continues, replace the ADIRU-1 (1FP1) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
(3) Do the test given in Para. 3.A.
- if the fault continues, do the next step.
(4) Do a check and repair the aircraft wiring (Ref. ASM 27-51/08).
(5) Do the test given in Para. 3.A.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 270
May 01/04R
CES R Flap Position Indication Disagree
1. Possible Causes
_______________
R - FWC-1 (1WW1)
R - FWC-2 (1WW2)
R - FLAP-PCU (6201CM)
R - PPU-INSTRUMENTATION (IPPU) (3CN)
2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R AMM 27-54-51-000-001 R R AMM 27-54-51-400-001 R R AMM 27-55-11-000-001 R AMM 27-55-11-400-001 R R AMM 31-53-34-000-001 R R AMM 31-53-34-400-001 R R ASM 27-55/01
3. Fault Confirmation
__________________ Removal of the Power Control Unit 6201CM of the Flap System Installation of the Power Control Unit 6201CM of the Flap System Removal of the Instrumentation Position Pick-Off Unit Installation of the Instrumentation Position Pick-Off Unit Removal of the Flight Warning Computer (FWC) (1WW1,1WW2) Installation of the Flight Warning Computer (FWC) (1WW1,1WW2)
R A. Make sure of the apparently incorrect Slat/Flap position indications on R the ECAM display. R
4. Fault Isolation
_______________
R A. If the apparently incorrect Slat/Flap position indications show on the
R ECAM display:
R - Pull circuit breaker of FWC 1 (1CN):
R (1) If the fault does not continue:
R - Replace the FWC 1 (1WW1) (Ref. AMM TASK 31-53-34-000-001) and (Ref.
R AMM TASK 31-53-34-400-001) FWC-1 (1WW1).
R - Reset the circuit breaker of FWC 1 (1CN).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞27-51-00∞∞∞∞∞∞∞∞∞∞Page 271
May 01/05 CES
R (a) If the fault continues:
R - Change the electrical connector 3CN-A with 3CN-B.
R 1_ If the fault does not continue:
R - Replace the PPU-INSTRUMENTATION (IPPU) (3CN) (Ref. AMM TASK
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) 飛行操縱 2(4)
