3. Job Set-up
__________
 Subtask 72-23-00-941-097

 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:
 (a) Put a warning notice to tell persons not to start the engine.
 F 『 EEFF : ALL E Page 66872-23-00
 E E May 01/05 E
RE ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:
 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 72-23-00-010-123
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 4. Procedure
_________
 Subtask 72-23-00-210-067
 A. Visual Inspection of the Junction Box
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
Crack on the two lateral On crack 0.78 in. (20  Stop crack by drilling a
 weldel latches. mm) max length.  0.12 in. (3 mm) hole at each ends of the crack. Clean the part.Apply RTV 732 (Material No. CP2242) or equivalent on the inner face of the affected area
 F 『 EEFF : ALL E Page 66972-23-00
 E E May 01/05 E E ECES E 5. Close-up

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

________ Subtask 72-23-00-410-115
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (3) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 67072-23-00
 E E May 01/05 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 FAN FRAME ASSEMBLY - REPAIRS

____________________________
 TASK 72-23-00-300-040
 Local Reconditioning of the Abradable Material- Defects less than 0.12 in. (3 mm) deep and 0.50 in.2 (3.2 cm2)
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific heat gun or a infra-red lamp
 No specific protective mats
 No specific spatula
 No specific vacuum cleaner
 No specific warning notice
 No specific access platform 0.5 m (1 ft. 8 in.)

 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP1039 *
 acetone (Ref. 70-30-00)
 Material No. CP1041 *

 isopropyl alcohol (Ref. 70-30-00) R Material No. CP2011 * R stoddard solvent (Ref. 70-30-00)
 Material No. CP2239 *
 abrasive cloth (Ref. 70-30-00)
 Material No. CP2297 *
 base RTV 147 A (Ref. 70-30-00)

 Material No. CP2298  *
 catalyst (hardener) RTV 147 B (black color)
 (Ref. 70-30-00)

R Material No. CP2559 *
R ardrox 552 (Ref. 70-30-00)

 F 『 EEFF : ALL E Page 80172-23-00
 E E May 01/05 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 -------------------------------------------------------------------------------

REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R Material No. CP2560 *
R turco ind 79 (Ref. 70-30-00)
R Material No. CP2566 *
R mag-chem teksol (Ref. 70-30-00)
R Material No. CP2584 *
R degreasol 99 R (Ref. 70-30-00)
R Material No. CP2656 *
R mag-chem skysol (Ref. 70-30-00)

 C. Referenced Information
 -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(7)