Maintenance
78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance
78-36-00-010-040 Opening of the Thrust Reverser Doors
78-36-00-410-040 Closing of the Thrust Reverser Doors
NDTM 720000
72-51-00-991-301 Fig. 602
3. Job Set-up
__________
Subtask 72-51-00-941-052
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
F 『 EEFF : ALL E Page 61372-51-00
E E Feb 01/02 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 72-51-00-010-057
B. Get Access
(1) Open the fan cowls doors: (Ref. TASK 71-13-00-010-040) FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR.
(2) Put the access platform in position. Subtask 72-51-00-040-052
C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 72-51-00-010-058
D. Open the thrust reverser cowl doors (Ref. TASK 78-36-00-010-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR.
4. Procedure
_________ (Ref. Fig. 602/TASK 72-51-00-991-301) Subtask 72-51-00-010-059
A. Remove parts before borescope inspection.
(1) Remove the borescope plugs from the approximate 3 and 10 o'clock positions on the combustion case.
F 『 EEFF : ALL E Page 61472-51-00
E E Feb 01/02 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Subtask 72-51-00-290-054
B. Do a Borescope Inspection
(1) Connect the fiber light cable to the BORESCOPE KIT (856A1320 P04 or P05), and to the port on BORESCOPE - LIGHT SOURCE SET (856A1322 P02 or P03 or P04 or P07 or P08).
NOTE : Use the MONITOR, RESOLUTION BORESCOPE (856A1323G01) to make
____ sure the borescope or the fiberscope and the light source are serviceable. See the Non-Destructive Test Manual for this procedure (Ref. NDTM 720000).
(2) Put the rigid borescope, of the BORESCOPE KIT (856A1320/P04 or P05), into the ports and turn on the light source BORESCOPE - LIGHT SOURCE SET (856A1322/PO3 or PO4).
(3) Rotate and adjust the borescope to view the HPT nozzle area.
(4) If inspection of the nozzle convex side is necessary, use a FIBERSCOPE SET (856A1321 P01 or P03) and KIT, BORESCOPE GUIDE - HP TURBINE (856A1310G01), or GUIDE TUBE ,BORESCOPE - HPT SHROUD (856A1351P01).
NOTE : If KIT, BORESCOPE GUIDE - HP TURBINE (856A1310) is used to
____ view the convex side, an 8 ft. (2.43 m) fiberscope must be used.
(5) Inspect the following:
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Leading edge of vane
airfoil for:
A. Cracks. Any number, 0.3 in. See limit extension
(7.62 mm) long ; no (Ref. TASK 72-00-00-200-missing material. 025).
B. Other cracks (not Any number, 0.5 in. See limit extension interconnecting (12.7 mm) long; no (Ref. TASK 72-00-00-200-nose holes). missing material. 025).
R C. Baffle.
F 『 EEFF : ALL E Page 61572-51-00
E E May 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------R NOTE : The airfoil's baffle is visible inside the airfoil when missing
____ R material occurs. It is sheet metal with cooling holes.
R (1) Cracks.
R (2) Missing R material. R
R D. Burns or missing material.
R E. Missing thermal barrier coating (TBC).
2. Concave surface of vane airfoil for:
A. Cracks.
B. Burns or missing material.
C. Missing thermal barrier coating (TBC).
3. Convex surface of vane airfoil for:
A. Radial cracks.
Any number.
Any area equivalent to a rectangle defined by 4 adjacent holes.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(55)
