R Sealol Seal Assembly (Typical) Figure 801/TASK 72-63-00-991-305
F EEFF : E E ECES ALL 『E 72-63-00EEE Page 805 May 01/02
Removal/Istallation of a Sealol Seal Rotating Mating Ring (Typical)
Figure 802/TASK 72-63-00-991-306
F EEFF : ALL 『E 72-63-00 Page 806
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Subtask 72-63-00-020-059
B. Removal of the Sealol Seal Housing Assembly
(1) Remove the 3 nuts (60) and washers (50) which attach the sealol seal housing assembly (40) to the drive pad.
(2) Remove the sealol seal housing assembly (40) with the jackscrews P2 from the TOOL SET - JACK SCREW (856A1130G09). Remove and discard O-ring (30).
(3) Put the removed parts (60), (50) and (40) in the storage box.
Subtask 72-63-00-020-060
C. Removal of the Rotating Mating Ring Assembly
(1) Depending on the drive pad from which you remove the rotating mating ring assembly, get the applicable tool diameter configuration from the tool set, SEALOL AND MAGNETIC SEALS - R/I (856A3576G01).
- for the fuel pump and hydraulic pump drive pads, use the smaller diameter tool with the items P09, P10 and P11
- for the starter and IDG drive pads, use the larger diameter tool with the items P02, P03 and P06.
(2) Loosen the tool items:
- P06 and P05 (larger diameter tool) or
- P11 and P05 (smaller diameter tool).
(3) Engage the tool on the gearshaft until the nylon/viton-end of item:
- P02 (larger diameter tool) or
- P09 (smaller diameter tool) Comes against the polished face of the rotating mating ring.
(4) Tighten the item P05 by hand until you feel the jaws of the collet are tightly engaged under the mating ring. Manually give the tool one or two pulls to make sure it is correctly installed. If so, it must not come out.
(5) Install the slide hammer on top of the tool. Operate the slide hammer and remove the rotating mating ring assembly from the gearshaft.
PRE SB CFM 72-105
F 『 EEFF : ALL E Page 80772-63-00
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(6) Remove the O-ring (10) from the inner diameter groove of the rotating mating ring (20). Discard the O-ring (10).
POST SB CFM 72-105
(7) Remove the bal seal (15) from the inner diameter groove of the rotating mating ring (20) for the IDG pad and starter pad. Discard the bal seal (150). Remove the O-ring (10) from the inner diameter groove of the rotating mating ring (20) for the fuel pump pad and hydraulic pump pad. Discard the O-ring (10). END OF SB CFM 72-105
(8) Loosen the items:
- P06 and P05 (larger diameter tool) or
- P11 and P05 (smaller diameter tool) And remove the rotating mating ring (20) from tool (856A3576G01). Put the mating ring (20) in the storage box.
Subtask 72-63-00-020-061
D. Disposal of the Removed Sealol Seal Components
(1) Tag the removed parts (40) and (20) to indicate they come from the same matched assembly.
(2) Put the removed parts in a storage box and send them to the repair shop.
Subtask 72-63-00-420-059
E. Preparation for the Installation of the Sealol Seal Assembly
(1) Get a new sealol seal assembly corresponding to the diameter of the drive pad on which you do the replacement.
(2) Clean the gearshaft area
CAUTION : DO NOT USE THIS SOLVENT NEAR FLAMES OR HEAT, BECAUSE THIS
_______ SOLVENT IS FLAMMABLE. DO NOT BREATHE THE GASES RELEASED FROM SOLVENT, DO NOT LET IT TOUCH YOUR SKIN OR CLOTHING AND MAKE SURE YOU HAVE A GOOD FLOW OF AIR, BECAUSE THIS SOLVENT IS DANGEROUS TO YOUR SKIN, EYES AND LUNGS.
F 『 EEFF : ALL E Page 80872-63-00
E E May 01/05 ERE
ECES E F 『 EEFF : ALL E Page 80972-63-00
F 『
E C F M E
E E
E 56-5B E
E E
R R R R R R (a) Clean the gearshaft area to come in contact with the new rotating mating ring (20) with acetone (Material No. CP1039) or isopropyl alcohol (Material No. CP1041) or stoddard solvent (Material No. CP2011) or ardrox 552 (Material No. CP2559) or turco ind 79 (Material No. CP2560) or mag-chem teksol (Material No. CP2566) or degreasol 99 R (Material No. CP2584) or mag-chem skysol (Material No. CP2656).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發(fā)動機 2(149)
