(5) Safety the nipple (180) to the oil inlet cover (160) with lockwire

 0.032 in. (0.8 mm) dia (Material No. CP8001) or lockwire 0.032 in.
 (0.8 mm) dia (Material No. CP8002).

 (6) Lubricate a new O-ring (20) with engine oil (Material No. CP2442).

 (7) Install the O-ring (20) in the front groove on the oil inlet cover (160).

 (8) Position a new Gasket seal (230) on the oil inlet cover (160).

 (9) Lubricate the threads of the bolts (30) with graphite grease (Material No. CP2101).

 (10) Install the oil inlet cover (160) with the ADAPTER, PULLER - OIL INLET COVER (856A3419G02), in the LPT frame. Match the position of the oil inlet cover flange with the oil scavenge tube which comes out at the bottom of the No. 5 bearing support.

 (11) Attach the oil inlet cover (160) to the No. 5 bearing support with bolts (30).

 (12) TORQUE the bolts (30) to between 110 and 120 lbf.in (1.24 and 1.35 m.daN).

 (13) Safety bolts with lockwire 0.032 in. (0.8 mm) dia (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia (Material No. CP8002).

 **ON A/C 001-049, 052-099, 101-105, 151-154, 201-207,
 Subtask 72-56-00-420-053
 B. Installation of the Oil Supply Tubes CAUTION : MAKE SURE THAT THE SLEEVE LOCKING NUT OF THE OIL SUPPLY TUBE IN
_______
 THE LPT FRAME HUB IS LOOSENED.

 NOTE : For Turbine Frame with Radial Struts only.
____
 F 『R EEFF : 001-049, 052-099, 101-149, 151-199, E Page 43272-56-00
 E E201-299, 301-399, 401-499, Aug 01/05 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (1) Make sure that the sleeve locking nut (110) is loosened and remove
 the two bolts (130) which attach the end fitting (120) to the LPT
 frame.

 (2) Put the oil supply tube (40) and the damping oil tube (70) in
 position.

 (3) Connect the damping oil tube (70) to the nipple (90) of the No. 5 bearing support and to the oil supply tube (40). Tighten the coupling nuts by hand.

 (4) Connect the oil supply tube (40) to the nipple (50) and to the oil
 supply tube (140). Tighten the coupling nuts by hand.

 (5) Lubricate the threads of the bolts (130) with graphite grease
 (Material No. CP2101).

 (6) Attach the end fitting (120) to the LPT frame with bolts (130).

 (7) Tighten the sleeve locking nut (110) by hand.

 (8) Make sure the oil tubes are installed without strain.

 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
 (9) TORQUE both coupling nuts of the damping oil tube (70) to between 90 and 100 lbf.in (1.01 and 1.13 m.daN).
 (10) Safety the coupling nuts with lockwire 0.032 in. (0.8 mm) dia (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia (Material No. CP8002).

 (11) TORQUE both coupling nuts of the oil tube (40) to between 270 and 300 lbf.in (3.05 and 3.39 m.daN).

 (12) Safety the coupling nuts with lockwire 0.032 in. (0.8 mm) dia (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia (Material No. CP8002).

 (13) TORQUE the sleeve locking nut (110) to between 50 and 55 lbf.in (0.56 and 0.62 m.daN).

 (14) Safety the sleeve locking nut (110) with lockwire 0.032 in. (0.8 mm) dia (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia (Material No. CP8002).

 F 『 EEFF : 001-049, 052-099, 101-105, 151-154, E Page 43372-56-00
 E E201-207, Aug 01/05 ERE
ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (15) TORQUE the two bolts (130) to between 110 and 120 lbf.in (1.24 and

 1.35 m.daN).

 (16) Safety bolts (130) with lockwire 0.032 in. (0.8 mm) dia (Material No. CP8001) or lockwire 0.032 in. (0.8 mm) dia (Material No. CP8002).

 **ON A/C 051-051,
 Subtask 72-56-00-420-053-B
 B. Installation of the Oil Supply Tubes NOTE : This procedure is for Turbine Frame with Tangential Non Symetrical
____
 Section Struts only.

 NOTE : Make sure that Oil Supply Tube in the LPT frame is correctly
____
 positioned.

 (1) Put the oil supply tube (40) and the damping oil tube (70) in position.

 (2) Connect the damping oil tube (70) to the nipple (90) of the No. 5 bearing support and to the oil supply tube (40). Tighten the coupling nuts by hand.

 (3) Connect the oil supply tube (40) to the nipple (50) and to the oil supply tube (100). Tighten the coupling nuts by hand.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(111)