(2)
Make sure that the WARNING NOTICE are in position to tell persons not to pressurize the Blue hydraulic system:
-In the cockpit on the hydraulic section 40VU of the overhead panel
-On the ground service panel of the Blue hydraulic system.
(3)
Make sure that the Blue hydraulic system is depressurized and put it in the maintenance configuration. (Ref. TASK 29-00-00-864-001).
(4)
Make sure that the reservoir of the Blue hydraulic system is depressurized (Ref. TASK 29-14-00-614-001).
(5)
Make sure that the access door 195BB is open . Subtask 29-12-22-865-051
B.
Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU HYD/HYD PWR/B WARN/& CTL 2702GJ C12 121VU HYDRAULIC/SOL VALVES/G/Y/B/LEAK/TST 1881GP N35 123VU B HYD/ELEC PUMP 2701GJ AB09
4. Procedure
_________
(Ref. Fig. 401/TASK 29-12-22-991-001) Subtask 29-12-22-420-050
A. Installation of the Gas Charging-Valve
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Remove the PLUG - BLANKING from the adapter (2).
(4)
Remove the CAP - BLANKING from the gas charging-valve (4).
(5)
Apply the HYDRAULIC FLUIDS (Material No. 02-003) to the threads of the gas charging-valve (4) connection.
(6)
Make sure that the 0-ring seal (3) is installed on the gas charging-valve (4).
(7)
If the removed charging-valve (4) is to be installed, remove the used 0-ring seal (3) and install a new o-ring (3)
(8)
Install the gas charging-valve (4) on the adapter (2).
(9)
TORQUE the gas charging-valve (4) to between 1.42 and 1.54 m.daN
(10.47 and 11.35 lbf.ft).
(10) Safety the gas charging-valve (4) with the lockwire MISCELLANEOUS (Material No. 19-010).
Subtask 29-12-22-860-052
B. Preparation for Test
(1)
Fill the accumulator with nitrogen (Ref. TASK 12-14-29-614-001).
(2)
Close the gas charging-valve nut (5).
(3)
Torque the gas charging-valve nut (5) to between 0.3 and 0.6 m.daN
(26.54 and 53.09 lbf.in).
(4)
Remove the WARNING NOTICE from the cockpit and the ground service panel.
(5)
Pressurize the reservoir of the Blue hydraulic system (Ref. TASK 29-14-00-614-002).
(6)
Make sure that the fluid level in the reservoir of the Blue hydraulic system is correct. Add fluid as necessary (Ref. TASK 12-12-29-611-001).
(7)
Pressurize the Blue hydraulic system (Ref. TASK 29-10-00-863-003). Subtask 29-12-22-790-050
C.
Test
(1) Apply the leak detector SPECIAL MATERIALS (Material No. 05-004) to the connections of the gas charging-valve (4), the adapter (2) and the endcap (6). Make sure that there are no leaks.
5. Close-up
________ Subtask 29-12-22-860-053
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access door 195BB.
Subtask 29-12-22-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1881GP, 2701GJ, 2702GJ.
RELIEF VALVE (2063GM) - REMOVAL/INSTALLATION
____________________________________________
TASK 29-12-32-000-001
Removal of the Pressure Relief Valve of the Blue Hydraulic System (2063GM)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓3(40)
