(16)
Hold the manifold (26) and remove the two bolts (61) and the two washers (62).
(17)
Remove the manifold (26).
(18)
Install blanking plugs on the disconnected line ends and the manifold ports.
R **ON A/C 059-099, 102-149, 151-199, 201-299, 301-399, 401-499,
Subtask 29-12-14-020-050-A
A. Removal of the HP Manifold CAUTION : USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN
_______ YOU DISCONNECT/CONNECT HYDRAULIC LINES ON UNIONS. IF YOU USE THE SECOND WRENCH, YOU WILL NOT LOOSEN OR TIGHTEN THE UNION TOO MUCH.
(1)
Disconnect the electrical connectors (20),(29),(32),(33).
(2)
Put blanking caps on the disconnected electrical connectors.
(3)
Cut and remove the tie wraps as necessary.
(4)
Remove the cable clamps as necessary.
(5)
Loosen the pipe end-fittings (47),(74) and remove the pipe (48).
(6)
Loosen the pipe end-fittings (6),(77) and remove the pipe (5).
(7)
Loosen the pipe end-fittings (10),(72) and remove the pipe (9).
(8)
Loosen the pipe end-fittings (59),(75) and remove the pipe (60).
(9)
Loosen the pipe end-fittings (56),(70) and remove the pipe (57).
(10)
Loosen the pipe end-fittings (65),(78) and remove the pipe (66).
(11)
Loosen the pipe end-fitting (52) and disconnect the pipe (53) from the union (51).
(12)
Loosen the pipe end-fitting and disconnect the pipe (53) from the Blue power accumulator 2070GM. Remove the pipe (53).
(13)
Loosen the pipe end-fitting (2) and disconnect the tee-connector (1) from the union (3).
(14)
Remove the two nuts (42) and the two bolts (41).
(15)
Hold the manifold (26) and remove the two bolts (61) and the two washers (62).
(16)
Remove the manifold (26).
(17)
Install blanking plugs on the disconnected line ends and the manifold ports.
R 1EFF : 059-099, 102-149, 151-199, 201-299, 1 29-12-14Page 411 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
**ON A/C ALL
TASK 29-12-14-400-001
Installation of the HP Manifold of the Blue Hydraulic System
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs No specific containers No specific plastic or wooden scraper No specific warning notices No specific 1 BAG - PLASTIC No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00
to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft)
B.
Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A CORROSION INHIBITING BRUSH CONSISTENCY (Ref. 20-31-00)
Material No. 09-018 USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00)
1EFF : ALL 1 29-12-14Page 412 1 1 May 01/05R 1 1 1CES 1
-------------------------------------------------------------------------------
REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 16-003 F ASNB70720
COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
Material No. 19-010 USA AMS 5687
LOCKWIRE STAINLESS STEEL ANNEALED 0.8MM DIA
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
11 O-ring
13 square-section seals
13 square-section seals
22 square-section seals
24 square-section seal
31 square-section seals
31 square-section seals
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓3(21)
