(2)
In the cockpit, make sure that the access panel (8) is removed.
(3)
Make sure that the access platform is in position at the access door 121AL.
(4)
Make sure that the access door 121AL is open.
(5)
Make sure that the external power connector is not connected to the aircraft receptacle.
(6)
Make sure that a warning notice is in position on the access door 121AL to tell persons not to use the external power receptacle.
(7)
In the cockpit, on the overhead ELEC panel 35VU, make sure that these pushbutton switches are released:
-BAT 1, BAT 2,
-APU GEN,
-GEN 1, GEN 2,
-EXT PWR.
(8)
In the cockpit, make sure that a warning notice is in position to tell persons not to operate the pushbutton switches on these overhead panels:
-21VU (EMER ELEC PWR),
-35VU (ELEC).
(9)
In the cockpit, on the APU section of the overhead panel 25VU, make sure that a warning notice is in position to tell persons not to start the APU.
4. Procedure
_________
**ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
(Ref. Fig. 401/TASK 24-41-55-991-001) R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 24-41-55-991-001-A)
**ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
Subtask 24-41-55-420-051
A. Installation of the Contactor Base CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(1)
Install the contactor base (6) in correct position.
(2)
Install the four screws (19) and washers (18) and tighten them.
(3)
Make sure that the electrical cables (14) are clean and in correct condition.
(4)
Install the cables (14).
(5)
Install the nuts (12) and the washers (13) and tighten them.
(6)
If the base has the components that follow:
(a)
Install the three electrical wires (11).
(b)
Install the screws (10) and the washers (9) and tighten them.
(7)
Install the jumpers (17) between the base (6) and the adjacent bases.
(8)
Install the washers (15) and the nuts (16) and tighten them (Ref. TASK 20-21-15-912-001).
R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
Subtask 24-41-55-420-051-A
A. Installation of the Contactor Module CAUTION : REFER TO THE MATCH MARKS MADE DURING THE REMOVAL WHEN YOU
_______ CONNECT THE ELECTRICAL WIRES. INCORRECT CONNECTION OF THE WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
(1)
Install the contactor module (5) in correct position.
(2)
Install the eight screws (16) and washers (15) and tighten them.
(3)
Make sure that the electrical cables (14) are clean and in correct condition.
(4)
Install the cables (14).
(5)
Install the nuts (13) and the washers (12) and tighten them.
(6)
If the base has the components that follow:
(a)
Install the electrical wires (11).
(b)
Install the screws (10) and the washers (9) and tighten them.
(7)
Install the jumpers (17) between the module (5) and the adjacent modules.
(8)
Install the washers (19) and the nuts (18) and tighten them (Ref. TASK 20-21-15-912-001).
R **ON A/C ALL
Subtask 24-41-55-420-050 R B. Installation of the Contactor
(1)
Install the contactor (3) on the 6 tapped barrels (5) of the contactor base (6).
(2)
TORQUE the six captive screws (2) to between 0.50 and 0.60 m.daN
(44.24 and 53.09 lbf.in).
(3)
Remove the blanking caps from the electrical connectors.
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5)
Connect the electrical connector (1).
Subtask 24-41-55-710-050 R C. Test of the External Power Supply
(1) Make sure that the aircraft electrical circuits are correctly energized with the external power supply (Ref. TASK 24-41-00-861-002).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(91)
