曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R 
R  The GAPCU stops normal mode transmission and enters the 
R  interactive mode when it receives the order from the CFDIU. The 
R  GAPCU transmits the EPGS (External Power Generation System) main 
R  menu. 
R 
R  The EPGS main menu comprises eight functions which are: 
R  (Ref. Fig. 007A) 
R  - LAST LEG REPORT, 
R  - PREVIOUS LEGS REPORT, 
R  - LRU IDENTIFICATION, 
R  - GROUND REPORT, 
R  - TROUBLE SHOOTING DATA, 
R  - CLASS 3 FAULTS REPORT, 
R  - TEST, 
R  - SPECIFIC DATA. 
R 
R  The content of each function is described in Para. B. 
R  (Description of the Interactive Mode Function) 
R  For more information: Ref. 31-32-00 (CFDIU). 
R  (4) Communication with (up to) the two GCUs 
R 
R  (Ref. Fig. 008) 
R  The GAPCU transmits command and data to and receives data from up to 
R  the two GCUs (GCU 1, 2). 
R  The communication is made via MIL-STD-1553-B link. 
R 
R  The GAPCU is able to read fault data from its own BITE and from the 
R  NVMs in each GCU on the ground or in flight. 
R  The GAPCU is able to initiate its own and each GCUs maintenance BITE 
R  when requested by the CFDS. 
R  If the GAPCU has lost the communication with a GCU, it generates a 
R  message to the CFDS indicating the failed GCU communication. 
R  (5) Detection of any failure affecting the external power channel. 
R 
R  Ref. Para. C.(BITE/TEST Function). 
R  (6) Identification of the LRU responsible for the failure. 
R 
R  Ref. Para. C. (BITE/TEST Function).

 

R  (7) Memorization of the information pertaining to the failure in the Non 
R  Volatile Memory (NVM) 
R 
R  The GAPCU contains a NVM. The NVM is implemented on the EEPROM. Any 
R  fault identified by the GAPCU BITE is recorded in the GAPCU NVM. 
R  The GAPCU NVM is structured like the other type 1 computers (Ref. 
R  31-32-00)-(CFDIU). 
R  E. Description of the Interactive Mode Function 
R 
R  (Ref. Fig. 009, 010, 011, 012, 013, 014, 015) 
R  F. BITE Test Function 
R 
R  The GAPCU has an initialization test capability and three different types 
R  of BITE: 
R  - signature/monitor, 
R  - isolation, 
R  - maintenance. 
R 
R  Isolation BITE has the highest priority followed by maintenance BITE and 
R  then signature BITE. 
R  (1) TEST initialization 
R 
R  Test initialization is made at power up, when the ELEC/EXT pushbutton 
R  switch is cycled and the watchdog has timed-out or after a 
R  maintenance BITE request. 
R  (2) Signature/monitor BITE 
R 
R  Monitoring is performed as long as the GAPCU is powered except when 
R  the BITE is bypassed or if the maintenance BITE or isolation BITE has 
R  precedence. 
R  The monitor BITE does not change the contents of any RAM used by the 
R  control and protection software. It does not change the state of any 
R  of the outputs nor stimulate any sense circuitry. 
R  Once a given fault has been determined an indication of the fault is 
R  written in the NVM. 
R  If the same fault is detected again during the current flight, the 
R  number of occurrences of that fault is also indicated, up to a 
R  maximum of four times.

 

R EPGS - Maintenance Operation : LAST LEG REPORT R Figure 009
 1EFF : 401-499, 1 24-41-00Page 54 1 1 Aug 01/05 1 1 1CES 1

 INTENTIONALLY BLANK

 1 1

24-41-00Page 55
1 1 Aug 01/05 1 1 1CES 1R EPGS - Maintenance Operation : PREVIOUS LEGS REPORT R Figure 010 (SHEET 1)

 1EFF : 401-499, 1 24-41-00Page 56 1 1 Aug 01/05 1 1 1CES 1R EPGS - Maintenance Operation : PREVIOUS LEGS REPORT R Figure 010 (SHEET 2)

 1EFF : 401-499, 1 24-41-00Page 57 1 1 Aug 01/05 1 1 1CES 1R EPGS - Maintenance Operation : LRU IDENTIFICATION R Figure 011

 1EFF : 401-499, 1 24-41-00Page 58 1 1 Aug 01/05 1 1 1CES 1R EPGS - Maintenance Operation : GROUND REPORT R Figure 012
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(75)