(4)
Disengage the contactor (3) from the base (5) and remove the contactor.
____
from the contactor (3).
Contactors
Figure 401/TASK 24-38-55-991-001
1EFF : ALL 1 24-38-55 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 24-38-55-400-001 Installation of the Battery Line Contactor (6PB1, 6PB2) WARNING : MAKE SURE THAT NO AC OR DC POWER IS CONNECTED TO THE AIRCRAFT
_______ ELECTRICAL CIRCUITS. THERE IS A RISK OF ELECTROCUTION IF THE AC OR DC POWER STAYS CONNECTED.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
No specific access platform 0.5 m (1 ft. 8 in.)
No specific access platform 1.8 m (5 ft. 11 in.)
No specific Torque Wrench : range 33.63 to 41.6 lbf.in
(0.38 to 0.47 m.daN)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-38-00-710-001 Operational Test of the Battery Charge Limiter (BCL), (with the CFDS) 24-38-55-991-001 Fig. 401
3. Job Set-up
__________ Subtask 24-38-55-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is in position at the access door
822.
(2)
Make sure that the access door 822 is open.
(3)
Make sure that the access platform is in position at the access door
121AL.
(4)
Make sure that the access door 121AL is open.
(5)
Make sure that the external power connector is not connected to the aircraft receptacle.
(6)
Make sure that a warning notice is in position on the access door 121AL to tell persons not to use the external power receptacle.
(7)
In the cockpit, on the overhead ELEC panel 35VU, make sure that these pushbutton switches are released:
-BAT 1, BAT 2,
-APU GEN,
-GEN 1, GEN 2,
-EXT PWR.
(8)
In the cockpit, make sure that a warning notice is in position to tell persons not to operate the pushbutton switches on these overhead panels:
-21VU (EMER ELEC PWR),
-35VU (ELEC).
(9)
In the cockpit, on the APU section of the overhead panel 25VU, make sure that a warning notice is in position to tell persons not to start the APU.
4. Procedure
_________
(Ref. Fig. 401/TASK 24-38-55-991-001)
Subtask 24-38-55-420-050
A. Installation of the Contactor
CAUTION : MAKE SURE THAT THE CONTACTOR LOCATING PIN IS CORRECTLY ENGAGED
_______ IN ITS RECESS LOCATED IN ONE POWER TERMINAL. THIS PREVENTS DAMAGE TO THE LOCATING PIN WHEN YOU APPLY THE TORQUE.
(1)
Put the contactor (3) on the tapped barrels (6) of the contactor base (5).
(2)
TORQUE the captive screws (2) to between 33.63 and 41.6 lbf.in (0.38 and 0.47 m.daN).
(3)
Remove the blanking caps from the electrical connectors.
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5) Connect the connector (4) to the contactor (3). Subtask 24-38-55-710-050
B. Operational Test of the Battery Charge Limiter (BCL)
(1) Do an operational test of the BCL from the CFDS (Ref. TASK 24-38-00-710-001).
5. Close-up
________ Subtask 24-38-55-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Close the access door 822.
(4)
Close the access door 121AL.
(5)
Remove the access platform(s).
EXTERNAL POWER - DESCRIPTION AND OPERATION
__________________________________________
1. General
_______ The aircraft network can be supplied by a ground power unit. For this, an external power receptacle is provided forward of the nose landing gear well. This receptacle enables to supply:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(64)
