(e)
Wait until the battery contactor opens.
(f)
On the lower ECAM display unit, ELEC page, make sure that the battery voltage is above 25V and the battery discharge current is equal to or lower than 1A.
1_ After some 12 seconds, the green line between the BAT 1 (2)
indication and the DC BAT busbar indication:
- goes out of view if the battery charge is correct,
- stays in view if a battery charge is necessary.
NOTE : The time for the battery to charge is approximately 20____
minutes.
NOTE : The power consumption of the HOT bus is normally lower
____ than 100mA.
(g)
Swap the BCL 1 and the BCL 2.
(h)
Start a charging cycle of the battery which was related to the failed BCL during the previous flight.
(i)
On the ELEC panel 35VU, push the related BAT 2 (1) pushbutton switch to start the charging cycle of the battery 2 (1).
(j)
Release the BAT 1 (2) pushbutton switch related to the BCL not in operation.
R 1EFF : 001-049, 051-099, 101-149, 201-299, 1 24-30-00Page 403 1 1 May 01/05 1 1 1CES 1R **ON A/C 151-199, 301-399, 401-499,
Subtask 24-30-00-040-050-A
A. Do a charging cycle of the battery 1 (2) related to the BCL 1 (2) in operation.
(1)
on the ECAM control panel:
-push the ELEC key to get the ELEC system page.
(2)
In the cockpit, on the ELEC panel 35VU:
-push the related BAT 1 (2) pushbutton switch to start the charging cycle of the battery 1 (2).
(3)
On the lower ECAM display unit:
-
the green line between the BAT 1 (2) indication and the DC BAT busbar indication comes into view. The arrow points to the BAT 1
(2) indication,
-
the related parameter indications (voltage and current) come into view green.
(4)
On the ELEC system page, make sure that the ground power-unit voltage stays above 114VAC during the charge.
(5)
Wait until the battery contactor opens.
(a) After some 12 seconds, the green line between the BAT 1 (2) indication and the DC BAT busbar indication:
-goes out of view if the battery charge is correct,
-stays in view if a battery charge is necessary.
NOTE : The time for the battery to charge is approximately 20
____
minutes.
(6) On the lower ECAM display unit, ELEC page, make sure that the battery voltage is above 25V and the battery discharge current is equal to or lower than 1A.
NOTE : The power consumption of the HOT bus is normally lower than
____
100mA.
(7)
Swap the BCL 1 and the BCL 2.
(8)
Start a charging cycle of the battery which was related to the failed BCL during the previous flight.
R 1EFF : 151-199, 301-399, 401-499, 1 24-30-00Page 404 1 1 Aug 01/05 1 1 1CES 1
(9) On the ELEC panel 35VU, push the related BAT 2 (1) pushbutton switch to start the charging cycle of the battery 2 (1).
(10) Release the BAT 1 (2) pushbutton switch related to the BCL not in operation.
R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 24-30-00-040-051
B. Removal of the Battery 1(2)
(1) Remove the battery (Ref. TASK 24-38-51-000-001) only if:
-
the failure of the BCL 1(2) occurred on ground at power up, or
-
the time the aircraft was on ground was more than 3 hours.
(2) Send the battery 1(2) to the overhaul facility.
**ON A/C ALL
5. Close-up
________
Subtask 24-30-00-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access panel of the BATTERY power center 105VU.
(3)
Close the access door 822.
(4) Remove the access platform(s).
Subtask 24-30-00-860-053
B. Put the aircraft back to its initial configuration.
(1)
Do the EIS stop procedure
(Ref. TASK 31-60-00-860-002).
(2)
Put a warning notice in position in the cockpit to tell the crew that one BCL does not operate.
(3)
Make an entry in the logbook.
(4)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
INTENTIONALLY BLANK
R 1 1
24-30-00Page 406
1 1 May 01/04 1 1 1CES 1
TASK 24-30-00-440-001
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(26)
