(3)
 Loosen the 6 captive screws (2). NOTE : Do not remove the captive screws (2) and the spring washers

____
 from the contactor (3).

 (4) Remove the contactor (3).
 **ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,

 Subtask 24-41-55-020-051
 B. Removal of the Contactor Base CAUTION : MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU
_______ DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
 NOTE : The removal of the base is necessary only if the base is damaged.
____

 Contactor
 Figure 401/TASK 24-41-55-991-001

R 1EFF : 001-049, 051-062, 101-105, 151-152, 1 24-41-55Page 404 1201-205, 1May 01/05 1 1 1CES 1

 Contactor Figure 401A/TASK 24-41-55-991-001-A
R 1EFF : 063-099, 106-149, 153-199, 206-299, 1 24-41-55Page 405 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1

 (1)
 If the base has the components that follow:

 (a)
 Remove the screws (9) and the washers (10).

 (b)
 Disconnect the electrical wires (11).

 (2)
 Remove the nuts (12) and the washers (13).

 (3)
 Disconnect the cables (14) from the base (6).

 (4)
 Remove the nuts (15) and the washers (16).

 (5)
 Remove the jumpers (17) from the base (6) and from the adjacent bases.

 (6)
 Remove the four screws (19) and the four washers (18).

 (7) Remove the base (6). R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
 Subtask 24-41-55-020-051-A
 B. Removal of the Contactor Module CAUTION : MAKE MATCH MARKS ON ALL THE ELECTRICAL WIRES BEFORE YOU
_______ DISCONNECT THEM. INCORRECT CONNECTION OF WIRES WILL CAUSE DAMAGE TO EQUIPMENT.
 NOTE : The removal of the module is necessary only if the module is
____
 damaged.

 (1)
 If the module has the components that follow:

 (a)
 Remove the screws (9) and the washers (10).

 (b)
 Disconnect the electrical wires (11).

 (2)
 Remove the nuts (12) and the washers (13).

 (3)
 Disconnect the cables (14) from the module (5).

 (4)
 Remove the nuts (19) and the washers (18).

 (5)
 Remove the jumpers (17) from the module (5) and from the adjacent modules.

 (6)
 Remove the eight screws (16) and the eight washers (15).

 (7)
 Remove the module (5).

R 1EFF : 063-099, 106-149, 153-199, 206-299, 1 24-41-55Page 407 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL

 TASK 24-41-55-400-001
 Installation of the External Power Contactor (EPC)
 WARNING : MAKE SURE THAT NO AC OR DC POWER IS CONNECTED TO THE AIRCRAFT
_______
 ELECTRICAL CIRCUITS.
 THERE IS A RISK OF ELECTROCUTION IF THE AC OR DC POWER STAYS
 CONNECTED.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 0.5 m (1 ft. 8 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
20-21-15-912-001 Tightening Torques for Electrical Component Fasteners 24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
 from the External Power
 25-11-41-000-001 Removal of the Third Occupant Seat
 25-11-41-400-001 Installation of the Third Occupant Seat

R **ON A/C 001-049, 051-062, 101-105, 151-152, 201-205,
 24-41-55-991-001 Fig. 401 -------------------------------------------------------------------------------

REFERENCE DESIGNATION
 -------------------------------------------------------------------------------

R **ON A/C 063-099, 106-149, 153-199, 206-299, 301-399, 401-499,
 24-41-55-991-001-A Fig. 401A
 **ON A/C ALL
 3. Job Set-up
__________
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ELECTRICAL POWER 電源2(90)