R 1EFF : 301-399, 1 23-33-00Page 9 1 1 Nov 01/04 1 1 1CES 1
-------------------------------------------------------------------------------FIN I FUNCTIONAL DESIGNATION I PANEL I ZONE I ACCESS I I I I DOOR -------------------------------------------------------------------------------8MK MAIN MULTIPLEXER 88VU 128 10MK AUDIO REPRODUCER 88VU 128 50MK WALL DISCONNECT BOX 200 100MK SEAT ELECTRONIC BOX 200 200MK PASSENGER CONTROL UNIT 200 201MK PASSENGER CONTROL UNIT 200 202MK PASSENGER CONTROL UNIT 200 204MK TRANSDUCER 200 800MK RELAY 2000VU 220 801MK RELAY 187VU 128 120RH FLIGHT ATTENDANT PANEL 221
R **ON A/C 051-099, 106-149, 201-299, 301-399,
3. System Description__________________
R **ON A/C 051-099, 201-210,
R (Ref. Fig. 003)
R **ON A/C 051-099,
R (Ref. Fig. 004)
R **ON A/C 201-210,
R (Ref. Fig. 004A)
R 1EFF : 051-099, 106-149, 201-299, 301-399, 1 23-33-00Page 10 1 1 May 01/05 1 1 1CES 1
Passenger Entertainment System (PES) Interconnection
Figure 003
R 1EFF : 051-099, 201-210, 1 23-33-00Page 11 1 1 May 01/05 1 1 1CES 1
Passenger Entertainment System (PES) Interconnection
Figure 003A
R 1EFF : 106-149, 211-299, 1 23-33-00Page 12 1 1 May 01/05 1 1 1CES 1R Passenger Entertainment System (PES) Interconnection R Figure 003B
R 1EFF : 301-399, 1 23-33-00Page 13 1 1 Nov 01/04 1 1 1CES 1
R Passenger Entertainment System (PES).
R Figure 004
R 1EFF : 051-099, 1 23-33-00 Page 14
1 1 May 01/05
1 1
1CES 1
Passenger Entertainment System (PES) R Figure 004A
R 1EFF : 106-149, 201-299, 1 23-33-00Page 15 1 1 May 01/05 1 1 1CES 1R **ON A/C 051-099, 201-210,
A. BITE System The BITE system is assembled into the MPES. The Cabin Intercommunication Data System (CIDS) (Refer to 23-73-00) commands the MPES to go into the BITE mode. All input audio channels at the Main Multiplexer (MM) 8MK are electronically isolated from an active processing. A 400 Hz test tone is put on each of the channels. At the Seat Electronic Box (SEB) 100MK/ Passenger Control Units (PCUs) 200MK and 201MK all channels are examined for correct operation. Any failure data is transmitted back to the MM, the CIDS and the Central Fault Display System (CFDS) (Refer to 31-30-00).
B. PES Power Test When the PES power is on, the BITE automatically starts. Maintenance persons operate this test on command from the Programming and Test Panel (PTP) 110RH. An ARINC 429 high-speed bus transfers data between the CIDS and the MPES.
C. Audio Audio signals from the audio reproducer 10MK, and video audio, supply a minimum of eighteen audio channels to the MM. Circuits in the MM process this analog input and prepare it for conversion to digital data. These are sent to the SEB through the Wall Disconnect Boxes (WDB) 50MK.
D. Audio Output The SEB changes the MM digital audio, back to its original analog form. This audio output is transmitted to the passenger headsets through the Passenger Control Units (PCU).
E. Channels The audio signals in the MM can give a stereophonic channel. One monophonic channel from the Compact Disk (CD) reproducer is programmed as the left channel; the other monophonic channel is programmed as the right channel. Two monophonic channels give the effect of one stereophonic channel. Four channels from the CD reproducer can be used to provide boarding music over the loudspeakers in the cabin and in the lavatories.
F. Not Applicable
G. Not Applicable
H. Not Applicable
J. Not Applicable
R 1EFF : 051-099, 201-210, 1 23-33-00Page 16 1 1 May 01/05 1 1 1CES 1
K. Not Applicable
L. Not Applicable
R **ON A/C 106-149, 211-299,
R (Ref. Fig. 003A, 004A)
A. BITE System The BITE system is assembled into the MPES. The Cabin Intercommunication Data System (CIDS) (Refer to 23-73-00) commands the MPES to go into the BITE mode. All input audio channels at the Main Multiplexer (MM) 8MK are electronically isolated from an active processing. A 400 Hz test tone is put on each of the channels. At the Seat Electronic Box (SEB) 100MK / Passenger Control Units (PCUs) 200MK and 201MK all channels are examined for correct operation. Any failure data is transmitted back to the MM, the CIDS and the Central Fault Display System (CFDS) (Refer to 31-30-00).
B. PES Power Test When the PES power is on, the BITE automatically starts. Maintenance persons operate this test on command from the Programming and Test Panel (PTP) 110RH. An ARINC 429 high-speed bus transfers data between the CIDS and the MPES.
C. Audio Audio signals from the audio reproducer 10MK, and video audio, supply a minimum of sixteen audio channels to the MM. Circuits in the MM process this analog input and prepare it for the conversion to digital data. These are then sent to the SEB through the Wall Disconnect Boxes (WDB) 50MK.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(164)
