On the CAPT loud speaker:
-
the ground station gives the A/C identifaction which must be the same as the one your printing.
On the MCDU 2 scratchpad:
-
the VOICE "GO AHEAD" message comes into view.
At the bottom of the Engine/Warning Display (EWD):
-
the ACARS CALL message comes into view.
On the MCDU 2:
-
the MCDU MENU page comes into view.
On the MCDU 2:
-
the ACARS MENU page comes into view.
On the MCDU 2:
-
the page that includes all the received messages comes into view.
R 1EFF : 051-099, 1 23-24-00Page 510 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
R R 28. On the MCDU 2 keyboard: - push the MCDU MENU mode key.
R R R R 29. On the ECAM control panel: - push the CLR key until the MEMO section comes into view on the lower ECAM DU.
R R R R R R R 30. On the RMP 2: - push the transfer pushbutton switch (double arrow) between the two windows.
R R R
On the MCDU 2:
-the MCDU MENU page comes into view.
After not many seconds, on the RMP 2 (and RMP 3 if installed):
-
the ACARS indication shows in the STBY display window and the frequency (which was in the STBY display window of the RMP 2) shows in the ACTIVE display window.
At the bottom of the EWD (in the MEMO section):
-
the VOICE message comes into view.
R NOTE : If no ground station is available, you must do a reset of the ACARS____
R MU (pushbutton switch on the front face of the ACARS MU). This will
R prevent the queueing-up of the downlinks not sent.
R **ON A/C 001-049, 051-099, 101-105,
5. Close-up________
Subtask 23-24-00-860-050
R A. Put the aircraft back to its initial configuration.
R (1) On the RMP 1, set the ON/OFF selector switch to OFF.
R (2) Do the EIS Stop Procedure (Ref. TASK 31-60-00-860-002).
R (3) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-
002).
R 1EFF : 001-049, 051-099, 101-105, 1 23-24-00Page 511 1 1 May 01/05 1 1 1CES 1
R TASK 23-24-00-740-004 R BITE test of the ACARS R 1. Reason for the Job
__________________ R Self Explanatory R 2. Job Set-up Information
______________________ R A. Fixtures, Tools, Test and Support Equipment R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION R -------------------------------------------------------------------------------R No specific access platform 2.5 m (8 ft. 2 in.)
R B. Referenced Information R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 24-41-00-861-002 R R 24-41-00-862-002 R R 31-32-00-860-003 R
R 3. Job Set-up
__________
R Subtask 23-24-00-860-096 Energize the Aircraft Electrical Circuits from the External Power De-energize the Aircraft Electrical Circuits Supplied from the External Power Procedure to Get Access to the SYSTEM REPORT/TEST/COM Page
R A. Aircraft Maintenance Configuration
R (1) Energize the aircraft electrical circuits R (Ref. TASK 24-41-00-861-002). R (2) Do the procedure to get the SYSTEM REPORT/TEST/COM page. (Ref. TASK
R 31-32-00-860-003)
R (3) On the RMP 2, set the ON/OFF switch to ON.
R 1EFF : 001-049, 051-099, 101-105, 1 23-24-00Page 512 1 1 May 01/05 1 1 1CES 1
R Subtask 23-24-00-865-075
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(108)
