R B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AUTO FLT/MCDU/1 11CA1 B01 49VU L/G/LGCIU/SYS1/NORM 1GA C09 49VU FWS/FWC1/SPLY 3WW F01 121VU CFDS/CFDIU/SPLY 2TW J18 121VU DATA/LOADER/SPLY 3TD J16 121VU DLS&/DLRB/SPLY 5TD J15 121VU AUTO FLT/MCDU/2 11CA2 N20 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU EIS/FWC2/SPLY 2WW Q07
R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499,
4. Procedure
_________
R **ON A/C 401-499,
Subtask 23-28-00-970-053
A. Uploading of the USER-ORT part of the SATCOM Software
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:
-adjust the brightness of the
MCDU screen.
2.
Make sure that the SATCOM system On the MCDU, on the SATCOM menu page:
is in the logged-off condition. - the LOGGED-OFF or NOT AVAILABLE indication is shown.
3.
On the overhead panel, on the On the display of the DLS:
Data Loading Selector (DLS): - DB/N:
-set the ON/OFF switch to ON PUSH NEXT/PREV
indication is shown
On the MDDU:
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 23-28-00Page 302 1401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
4. On the overhead panel, on the DLS:
-push the PREV or NEXT key until you get the SATCOM indication
5. On the overhead panel, on the DLS:
-push the SEL CTL key.
6.
Get the SATCOM disks from the storage box.
7.
On the MDDU:
-push the USER-ORT disk into the disk drive, with the label in the forward direction.
8.
On the MDDU:
-remove the disk from the disk drive.
Subtask 23-28-00-865-071
-the < < MDDU READY > > indication is shown.
On the display of the DLS:
-SATCOMNOT SELECTEDindication is shown
On the display of the DLS:
-SATCOMSELECTED indication is shown
On the MDDU:
-the ready indication is shown,
-
then, the WAIT RESPONSE indication isshown,
-
then, the TRANSF IN PROG indication is shown.
NOTE : If more than one disk is
____ necessary to do the uploading of a same type of data, the EJECT DISK and INSERT NEXT DISK indications are shown one after the other. They tell the operator that he must put a new disk into the MDDU
-When the uploading is completed, the TRANSF COMPLETE indication is shown
On the MDDU:
-the < < MDDU READY > > indication isshown.
B. Open and close circuit breaker 102RV1 to do a reset of the SATCOM system.
R 1EFF : 401-499, 1 23-28-00Page 303 1 1 Aug 01/05 1 1 1CES 1
R **ON A/C 106-149, 151-199, 201-299, 301-399,
Subtask 23-28-00-280-052
C. Do a Check of the Identification of the Uploaded SATCOM Software
(1)
Do the procedure to get access to the SYSTEM REPORT/TEST page 2/6 ATA:23 COM (Ref. TASK 31-32-00-860-003)
(2)
Do a check of the identification of the loaded disk.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU: On the MCDU:
- push the line key adjacent to the SATCOM indication. - push the line key adjacent to the LRU IDENT indication. - the SATCOM menu page comes into view.- the LRU IDENTIFICATION page comesinto view.- on the LRU IDENTIFICATION page: make sure that the DB/N reference shown is the same as the DB/N reference on the disk(s).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM Communications 通訊1(139)
