4. Procedure
_________
(Ref. Fig. 401/TASK 22-81-12-991-002)
Subtask 22-81-12-420-052
A. Installation of the FCU
(1) Clean the component interface and/or the adjacent area.
(2) Do an inspection of the component interface and/or the adjacent area.
(3) Remove the blanking caps from the electrical connectors (2) and (7).
(4) Make sure that the electrical connectors (2) and (7) are in the correct condition.
(5) Connect the electrical connectors (2) and (7).
(6) Install the FCU (1) in its housing (8).
(7) Install the four screws (3) and washers (4).
(8) Close and hold the lower panel (6).
(9) Tighten the three Dzus fasteners (5) by a quarter turn.
Subtask 22-81-12-865-054
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 9CA1, 9CA2, 5LF
Subtask 22-81-12-710-052
R R C. Test
R (1) Do the Operational Test of the AFS (Ref. TASK 22-96-00-710-001).
R R R R NOTE : Additionally, you can do these operational tests (Ref. TASK____ 22-10-00-710-004) and (Ref. TASK 22-10-00-710-006). These two tests are optional.
R R (2) Do the Land CAT 3 Capability Test (Ref. TASK 22-97-00-710-001) if the aircraft operates in CAT 3 conditions.
1EFF : ALL 1 22-81-12Page 406 1 1 Nov 01/04 1 1 1CES 1
5. Close-up
________
Subtask 22-81-12-860-050
A. Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 22-81-12Page 407 1 1 Nov 01/01 1 1 1CES 1 MULTIPURPOSE CONTROL AND DISPLAY UNIT (MCDU) - DESCRIPTION AND OPERATION
________________________________________________________________________
1. General
_______
(Ref. Fig. 001)
The Multipurpose Control and Display Units (MCDU) provide access to the
following:
-FMGC (Flight Management function)
-DATA LINK (ACARS)-optional
-CFDS (Centralized Fault and Display System)
-AIDS-optional
-SAT (SATCOM)-optional
-ATSU-optional.
They are composed of a keyboard and a screen for data entry/display by the
pilot or the line maintenance personnel.
2. Component Location
__________________
(Ref. Fig. 002)
-------------------------------------------------------------------------------FIN | FUNCTIONAL DESIGNATION | PANEL|ZONE|ACCESS | ATA | | | | DOOR | REF.
-------------------------------------------------------------------------------3CA1 MCDU-1 11VU 211 831 22-82-12 3CA2 MCDU-2 11VU 211 831 22-82-12
3. Component Description
_____________________
R **ON A/C 001-003, 051-053,
A. MCDU Front Panel
(Ref. Fig. 003)
(1) The screen The MCDU display contains 14 lines, each having 24 characters. Of these 14 lines, the top line (line 1) is normally used as a title line or to display data to which the pilot does not have access. The bottom line (line 14) is the scratchpad line and is used by the pilot to alter the data in the data fields. Lines 2 through 13 are data lines arranged into six pairs (lines 2-3, 4 -5, 6-7, 8-9, 10-11, 12-13). Each pair of lines has a label line (the top of the two lines) and a data line. The data lines are adjacent to the line select keys, and the label line is just above the data line. The line pairs are referenced by line select keys as follows:
1EFF : ALL 1 22-82-00Page 1 1 1 May 01/05 1 1 1CES 1
R MCDU Interface Figure 001
1EFF : 1 1 1CES ALL 1 111 22-82-00 Page 2 May 01/03
R MCDU - Component Location Figure 002
1EFF : 1 1 1CES ALL 1 111 22-82-00 Page 3 May 01/03
MCDU Front Panel Figure 003
R 1EFF : 1 1 1CES 001-003, 051-053, 1 111 22-82-00 Page 4 May 01/05
Reference Screen lines 1L - 1R 2 - 3 2L - 2R 4 - 5 3L - 3R 6 - 7 4L - 4R 8 - 9 5L - 5R 10 - 11 6L - 6R 12 - 13
The line select keys allow entry of data into a field and access to a data or a function identified by that field.
(2)
The keyboard
(a)
Alphanumeric keys Pressing an alphanumeric key (O through 9, A through Z, . (full point), + (plus), - (minus) and / (slash)) enters that character into the scratchpad of the MCDU.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AUTO FLIGHT 自動飛行4(82)
