R R  Installation of the ABS1040-XXX Expension Joints Figure 202/TASK 20-26-00-991-003
 1EFF : 1 1 1CES  ALL  1 111 20-26-00 Page 204 Aug 01/02

R  2_  Carefully install the inner ring (2) with the spring on the
R  pressure side. 
R  (3) Lubricant 
R  (a) For ABS0737-XXX seals and Pre ABS1040-XXX 
R 
R  NOTE : The seals are supplied pre-lubricated and normally require____ 
R  no additional lubrication. In areas where installation is
 difficult (ducting angulation), you can apply a thin film
 of lubricant on the inner surface of the seal or on the
 sliding surface.
 Recommended lubricants:
 - For ABS0737-XXX seal type , use only COMMON GREASE
 (Material No. 04-007)
 - For other type of seals, use COMMON GREASE (Material No.
 04-007) or LUBRICANTS (Material No. 06-012). 
R  (b) For ABS1040-XXX 
R  Do not use lubricant for installation of ABS1040-XXX seals. 
R  (4) Duct connection 
R  (a) For ABS0737-XXX seals and Pre ABS1040-XXX 
R 
R  1_  Engage the male sleeve in the seal and connect the ducts. Make
R  sure that you do not cause damage to the seal during the 
R  operation. 
R 
R  2_  Align the two ducts on the same axis. Misalignment must not be
R  more than 3 degrees in all directions. 
R 
R  - Measure the distance "X" between the duct flanges "A" and 
R  B":
 (Ref. Fig. 201/TASK 20-26-00-991-001) 
R 
R  This distance must be the same (+/- 2 mm (0.078 in.)) around 
R  the full circumference of the duct to make sure that the two
 flanges are parallel. 
R  3_ Make sure that there are no side loads in the assembly.

R (b) For ABS1040-XXX

R  1_  Carefully install the male duct in the female sleeve and move
R  the duct around slightly to make the seal agree whith the 
R  shape of the duct 
R  2_  Align the two ducts on the same axis. Misalignment must not be
R  more than 3 degrees in all directions 
R  - Measure the distance "X" between the duct flanges "A" and 
R  B": 
R  (Ref. Fig. 201/TASK 20-26-00-991-001) 
R 
R  This distance must be the same (+/- 2 mm (0.078 in.)) around 
R  the full circumference of the duct to make sure that the two 
R  flanges are parallel. 
R  3_ Make sure that there are no side loads in the assembly.

 ELECTRICAL CABLES AND BUNDLES - MAINTENANCE PRACTICES
_____________________________________________________
 TASK 20-27-00-910-001
 Installation of Grommets

 1. Reason for the Job
__________________
 This procedure is applicable for the installation and bonding of the
 FLEXIFORM grommet.
 This installation prevents damage when the bundles go through holes in the
 structure.

 2. Job Set-up Information
______________________
 A. Consumable Materials
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
Material No. 08-10D  F ABS5093B485 MOISTURE BARRIER FOIL,SELF ADHESIVE (Ref. 20-31-00) R Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
20-27-00-991-001  Fig. 201 3. Job Set-up

__________ Subtask 20-27-00-869-050
 A. Preparation before Installation
 (Ref. Fig. 201/TASK 20-27-00-991-001)

 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1)
 Mating surfaces must be clean and degreased.

 (2)
 If not, clean the mating surfaces with CLEANING AGENTS (Material No. 11-003).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES-AIRFRAME(81)