-when you get the set swage torque values (after 15 to 20 seconds), the motor stops, the mandrels turns counterclockwise then moves to the rear,
-
the expander moves to the rear,
-
the cycle is completed.
(8)
Put the jaw switch on RELEASE.
(9)
Open the half jaws and remove the tube from the swage tool.
(10) Carefully clean the tube with CLEANING AGENTS (Material No. 11-003).
1EFF : ALL 1 20-23-11Page A236 1 1 Feb 01/05R 1 1 1CES 1
Subtask 20-23-11-917-067
D. Do the Check of the Swage
(1) Measure the diameter A, B and C and make sure that they obey the dimension acceptance criteria. (Ref. Fig. 254/TASK 20-23-11-991-047, 255/TASK 20-23-11-991-048)
NOTE : You must calculate the permitted min. and max. dia. C as a
____ function of the actual thickness of the tube before swaging.
NOTE : In all cases, you cannot re-swage.
____
(2)
Make sure that there are no scratches or other damage on the seal areas between sleeve and union.
(3)
Make sure that there are no scratches or roller marks on the tube
I.D.
NOTE : A helical extrusion mark in the G area (due to tube wall
____ growth during swaging) or a rubbing mark in the H area (due to swage tool cage rubbing) is permitted.
(4) Connect the HARRISON sleeve and union of the tubes and TORQUE it to the normal test value.
5. Close-up
________ Subtask 20-23-11-860-063
A. Put the aircraft back to its initial configuration.
(1)
Pressurize the hydraulic reservoirs (Ref. TASK 29-14-00-614-002).
(2)
If necessary, fill the hydraulic reservoirs:
-with a hand pump (Ref. TASK 12-12-29-611-001) - or with a hydraulic cart (Ref. TASK 12-12-29-611-002)
(3)
Pressurize the hydraulic systems:
-
for the Green system (Ref. TASK 29-10-00-863-001)
-
for the Yellow system (Ref. TASK 29-10-00-863-002)
-
for the Blue system (Ref. TASK 29-10-00-863-003).
1EFF : ALL 1 20-23-11Page A237 1 1 Feb 01/05R 1 1 1CES 1
(4)
Make sure that there is no leakage in the repaired area.
(a) If there is a leakage, slowly and continuously increase the torque value to the maximum approved (maximum test value) until you stop the leak.
(5)
Bleed the related hydraulic system:
(a)
For the Green system:
-
upstream of the engine pump (Ref. TASK 29-00-00-870-001)
-
upstream of the PTU (Ref. TASK 29-00-00-870-002)
-downstream of the engine pump (Ref. TASK 29-00-00-870-003).
(b)
For the Yellow system:
-
upstream of the engine pump (Ref. TASK 29-00-00-870-004)
-
upstream of the PTU (Ref. TASK 29-00-00-870-005)
-
upstream of the Yellow E-pump (Ref. TASK 29-00-00-870-006)
-downstream of the engine pump (Ref. TASK 29-00-00-870-007).
(c)
For the Blue sytem:
-upstream of the Blue E-pump (Ref. TASK 29-00-00-870-008)
-downstream of the Blue E-pump (Ref. TASK 29-00-00-870-009).
(d)
For the normal braking system (Ref. TASK 32-42-00-870-001).
(e)
For the alternate braking system.
-low pressure (Ref. TASK 32-43-00-612-001)
-high pressure (Ref. TASK 32-43-00-870-002).
(6)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 20-23-11Page A238 1 1 Feb 01/05R 1 1 1CES 1
TASK 20-23-11-300-006
Repair of the Hyraulic Tubes with CRYOFIT Couplings 3PHS111-XX
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific chipless roller-type cutter No specific deburring tool No specific scotch-brite pad No specific stop-watch No specific CRYOFIT Installation Tooling No specific Grade 400 emery cloth
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-003 USA ASTM D 740 METHYL-ETHYL-KETONE (Ref. 20-31-00)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STANDARD PRACTICES-AIRFRAME(44)
