LUBRICATION - DESCRIPTION AND OPERATION
_______________________________________
1. General
_______
The lubrication instructions define:
-Specification of the lubricant to be used
-Points to be lubricated
-
Special precautions to be observed.
A.
Equipment and Materials
Depending on the type of lubrication, use:
-a grease gun
-an oil can
-
a brush
-
a clean lint-free cloth
-an aerosol spray.
B.
Lubricant Specifications The lubricant references are given in the list of materials required for aircraft servicing and maintenance (Ref. ATA 20-31).
C.
General Requirements
(1)
Use only clean lubricants and tools for lubrication operations.
(2)
Before starting any lubricating operation, carefully clean the grease nipples lubricating holes. Lubrication must be accomplished immediately. Check that grease nipples and fitted with ball and spring.
(3)
Ensure that the old grease exudes through the pressure relief valves and on each side of the spherical bearings (unless the quantity of grease to be used is indicated).
(4)
After lubrication, remove all surplus grease. Wipe the grease nipple with a clean, lint-free cloth. Check that the ball and its spring are in position.
(5)
Before lubrication, the wheel bearings should be cleaned. The bearings should be lubricated and installed immediately.
D.
Lubrication Symbols
(Ref. Fig. 001)
The symbols used represent the recommended lubrication method.
Below each symbol, an index indicates:
-First term : the lubrication point location
-Second term : the lubricant to be used.
Lubrication Symbols
Figure 001
1EFF : ALL 1 12-22-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
FLIGHT CONTROLS - SERVICING
___________________________
TASK 12-22-27-640-003
Lubrication of Trimmable Horizontal Stabilizer Actuator Ball Screw Nut
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 274451-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific container 1l
No specific gun - grease
No specific pin - non-metallic
No specific safety barriers
No specific warning notice
No specific access platform 4.5 m (14 ft. 9 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 04-004 USA MIL-PRF-23827 TYPE I SYNTH.ESTER BASED GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 24-41-00-861-002
R
R 24-41-00-862-002
R
R 29-23-00-863-001
R
R
R 29-23-00-864-001
R
R 29-24-00-863-001
R
R 29-24-00-864-001
R 31-60-00-860-001
R 31-60-00-860-002
12-22-27-991-003
3. Job Set-up__________
Energize the Aircraft Electrical Circuits from the External Power De-energize the Aircraft Electrical Circuits Supplied from the External Power Pressurize the Green Hydraulic System from the Yellow Hydraulic System through the PTU with the Electric Pump Depressurize the Green and Yellow Hydraulic Systems after Operation of the PTU Pressurize the Yellow Hydraulic System with the Electric Pump Depressurize the Yellow Hydraulic System EIS Start Procedure EIS Stop ProcedureFig. 301 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM SERVICING 2
