曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Mode C (Altitude Reporting)
Primary radar returns indicate only range and bearing from
the radar antenna to the target; secondary radar returns can
display altitude, Mode C, on the control scope if the aircraft
is equipped with an encoding altimeter or blind encoder. In
either case, when the transponder’s function switch is in the
ALT position the aircraft’s pressure altitude is sent to the
controller. Adjusting the altimeter’s Kollsman window has
no effect on the altitude read by the controller.
Transponders, when installed, must be ON at all times when
operating in controlled airspace; altitude reporting is required
by regulation in Class B and Class C airspace and inside a
30-mile circle surrounding the primary airport in Class B
airspace. Altitude reporting should also be ON at all times.
9-4
Figure 9-5. Phonetic Pronunciation Guide.
Communication Procedures
Clarity in communication is essential for a safe instrument
flight. This requires pilots and controllers to use terms that
are understood by both—the Pilot/Controller Glossary in the
Aeronautical Information Manual (AIM) is the best source of
terms and definitions. The AIM is revised twice a year and
new definitions are added, so the glossary should be reviewed
frequently. Because clearances and instructions are comprised
largely of letters and numbers, a phonetic pronunciation guide
has been developed for both. [Figure 9-5]
ATCs must follow the guidance of the Air Traffic Control
Manual when communicating with pilots. The manual
presents the controller with different situations and prescribes
precise terminology that must be used. This is advantageous
for pilots because once they have recognized a pattern
or format they can expect future controller transmissions
to follow that format. Controllers are faced with a wide
variety of communication styles based on pilot experience,
proficiency, and professionalism.
Pilots should study the examples in the AIM, listen to
other pilots communicate, and apply the lessons learned
to their own communications with ATC. Pilots should ask
for clarification of a clearance or instruction. If necessary,
use plain English to ensure understanding, and expect the
controller to reply in the same way. A safe instrument flight
is the result of cooperation between controller and pilot.
Communication Facilities
The controller’s primary responsibility is separation of
aircraft operating under IFR. This is accomplished with ATC
facilities which include the AFSS, airport traffic control tower
(ATCT), terminal radar approach control (TRACON), and
air route traffic control center (ARTCC).
Automated Flight Service Stations (AFSS)
A pilot’s first contact with ATC is usually through AFSS,
either by radio or telephone. AFSSs provide pilot briefings,
receive and process flight plans, relay ATC clearances,
originate Notices to Airmen (NOTAMs), and broadcast
aviation weather. Some facilities provide En Route Flight
Advisory Service (EFAS), take weather observations,
and advise United States Customs and Immigration of
international flights.
Telephone contact with Flight Service can be obtained
by dialing 1-800-WX-BRIEF. This number can be used
anywhere in the United States and connects to the nearest
AFSS based on the area code from which the call originates.
There are a variety of methods of making radio contact:
direct transmission, remote communication outlets (RCOs),
ground communication outlets (GCOs), and by using duplex
transmissions through navigational aids (NAVAIDs). The
best source of information on frequency usage is the Airport/
Facility Directory (A/FD) and the legend panel on sectional
charts also contains contact information.
9-5
Figure 9-6. Flight Strip.
The briefer sends a flight plan to the host computer at
the ARTCC (Center). After processing the flight plan,
the computer will send flight strips to the tower, to the
radar facility that will handle the departure route, and to
the Center controller whose sector the flight first enters.
Figure 9-6 shows a typical strip. These strips are delivered
approximately 30 minutes prior to the proposed departure
time. Strips are delivered to en route facilities 30 minutes
before the flight is expected to enter their airspace. If a
flight plan is not opened, it will “time out” 2 hours after the
proposed departure time.
When departing an airport in Class G airspace, a pilot receives
an IFR clearance from the AFSS by radio or telephone. It
contains either a clearance void time, in which case an aircraft
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Flying Handbook儀表飛行手冊下(59)