曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

When flying the course indicated on the index, a left
deflection of the needle indicates a crosswind component
from the left. If the amount of correction brings the needle
back to center, decrease the left course correction by half. If
the CDI moves left or right now, it should do so much more
slowly, and smaller heading corrections can be made for the
next iteration.
Keeping the CDI centered will take the aircraft to the station.
To track to the station, the OBS value at the index is not
changed. To home to the station, the CDI needle is periodically
centered, and the new course under the index is used for the
aircraft heading. Homing will follow a circuitous route to the
station, just as with ADF homing.
To track FROM the station on a VOR radial, you should
first orient the aircraft’s location with respect to the station
and the desired outbound track by centering the CDI needle
with a FROM indication. The track is intercepted by either
flying over the station or establishing an intercept heading.
The magnetic course of the desired radial is entered under the
index using the OBS and the intercept heading held until the
CDI centers. Then the procedure for tracking to the station is
used to fly outbound on the specified radial.
Course Interception
If the desired course is not the one being flown, first orient
the aircraft’s position with respect to the VOR station and the
course to be flown, and then establish an intercept heading.
The following steps may be used to intercept a predetermined
course, either inbound or outbound. Steps 1–3 may be omitted
when turning directly to intercept the course without initially
turning to parallel the desired course.
1. Determine the difference between the radial to be
intercepted and the radial on which the aircraft is
located (205° – 160° = 045°).
2. Double the difference to determine the interception
angle, which will not be less than 20° nor greater
than 90° (45° x 2 = 090°). 205° + 090° = 295° for the
intercept)
3. Rotate the OBS to the desired radial or inbound
course.
4. Turn to the interception heading.
5. Hold this heading constant until the CDI center, which
indicates the aircraft is on course. (With practice in
judging the varying rates of closure with the course
centerline, pilots learn to lead the turn to prevent
overshooting the course.)
6. Turn to the MH corresponding to the selected
course, and follow tracking procedures inbound or
outbound.
Course interception is illustrated in Figure 7-16.
VOR Operational Errors
Typical pilot-induced errors include:
1. Careless tuning and identification of station.
2. Failure to check receiver for accuracy/sensitivity.
3. Turning in the wrong direction during an orientation.
This error is common until visualizing position rather
than heading.
4. Failure to check the ambiguity (TO/FROM) indicator,
particularly during course reversals, resulting
in reverse sensing and corrections in the wrong
direction.
5. Failure to parallel the desired radial on a track
interception problem. Without this step, orientation
to the desired radial can be confusing. Since pilots
think in terms of left and right of course, aligning the
aircraft position to the radial/course is essential.
6. Overshooting and undershooting radials on interception
problems.
7. Overcontrolling corrections during tracking, especially
close to the station.
8. Misinterpretation of station passage. On VOR
receivers not equipped with an ON/OFF flag, a
voice transmission on the combined communication
and navigation radio (NAV/COM) in use for VOR
may cause the same TO/FROM fluctuations on the
ambiguity meter as shown during station passage.
Read the whole receiver—TO/FROM, CDI, and
OBS—before you make a decision. Do not utilize a
VOR reading observed while transmitting.
9. Chasing the CDI, resulting in homing instead of
tracking. Careless heading control and failure to
bracket wind corrections make this error common.
7-15
HDG 025° CRS 025°
VOR1
025°
HDG 295° CRS 025°
VOR 1
295°
HDG 025° CRS 340°
VOR 1
025°
HDG 340° CRS 340°
VOR 1
340°
After needle centers
track inbound on
205° radial.
Maintain heading of
295°
Present position, inbound
on 160° radial.
Turn right to parallel desired
inbound course. Turn to 025°
heading for 205°radial.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Flying Handbook儀表飛行手冊下(17)