曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費(fèi)者

and numerous other oversights due to haste or
carelessness.
2. Improper alignment on the runway. This may result
from improper brake application, allowing the airplane
to creep after alignment, or from alignment with the
nosewheel or tailwheel cocked. In any case, the result
is a built-in directional control problem as the takeoff
starts.
3. Improper application of power. Abrupt application
of power complicates directional control. Add power
with a smooth, uninterrupted motion.
4. Improper use of brakes. Incorrect seat or rudder pedal
adjustment, with feet in an uncomfortable position,
frequently cause inadvertent application of brakes and
excessive heading changes.
5-30
Figure 5-41. Racetrack Pattern (Entire Pattern in Level Flight).
5. Overcontrolling rudder pedals. This fault may be
caused by late recognition of heading changes, tension
on the controls, misinterpretation of the heading
indicator (and correcting in the wrong direction),
failure to appreciate changing effectiveness of rudder
control as the aircraft accelerates, and other factors. If
heading changes are observed and corrected instantly
with small movement of the rudder pedals, swerving
tendencies can be reduced.
6. Failure to maintain attitude after becoming airborne.
If the pilot reacts to seat-of-the-pants sensations when
the airplane lifts off, pitch control is guesswork.
The pilot may either allow excessive pitch or apply
excessive forward elevator pressure, depending on the
reaction to trim changes.
7. Inadequate cross-check. Fixations are likely during trim
changes, attitude changes, gear and flap retractions,
and power changes. Once an instrument or a control
input is applied, continue the cross-check and note the
effect during the next cross-check sequence.
8. Inadequate interpretation of instruments. Failure to
understand instrument indications immediately indicates
that further study of the maneuver is necessary.
Basic Instrument Flight Patterns
Flight patterns are basic maneuvers, flown by sole reference
to the instruments rather than outside visual clues, for the
purpose of practicing basic attitude flying. The patterns
simulate maneuvers encountered on instrument flights
such as holding patterns, procedure turns, and approaches.
After attaining a reasonable degree of proficiency in basic
maneuvers, apply these skills to the various combinations of
individual maneuvers. The following practice flight patterns
are directly applicable to operational instrument flying.
Racetrack Pattern
1. Time 3 minutes straight-and-level flight from A to B.
[Figure 5-41] During this interval, reduce airspeed to
the holding speed appropriate for the aircraft.
2. Start a 180° standard rate turn to the right at B. Roll-out
at C on the reciprocal of the heading originally used
at A.
3. Time a 1 minute straight-and-level flight from C to D.
4. Start a 180° standard rate turn to the right at D, rollingout
on the original heading.
5. Fly 1 minute on the original heading, adjusting
the outbound leg so that the inbound segment is 1
minute.
NOTE: This pattern is an exercise combining use of the clock
with basic maneuvers.
Procedure Turn
A procedure turn is a maneuver that facilitates:
• A reversal in flight direction.
• A descent from an initial approach fix or assigned
altitude to a permissible altitude (usually the procedure
turn altitude).
• An interception of the inbound course at a sufficient
distance allowing the aircraft to become aligned with
the final approach.
Procedure turn types include the 45° turn, the 80/260 turn, and
the teardrop turn. All of these turns are normally conducted no
more than 10 nautical miles (NM) from the primary airport.
The procedure turn altitude generally provides a minimum
of 1,000' obstacle clearance in the procedure turn area (not
necessarily within the 10 NM arc around the primary airport).
Turns may have to be increased or decreased but should not
exceed 30° of a bank angle.
Standard 45° Procedure Turn
1. Start timing at point A (usually identified on approach
procedures by a fix). For example, fly outbound on a
heading of 360° for a given time (2 minutes, in this
example). [Figure 5-42]
2. After flying outbound for 2 minutes (point B), turn left
45° to a heading of 315° using a standard rate turn.
After roll-out and stabilizing, fly this new heading
of 315° for 40 seconds and the aircraft will be at the
approximate position of C.
5-31
Figure 5-42. Standard Procedure Turn (Entire Pattern in Level
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Instrument Flying Handbook儀表飛行手冊上(96)