NOTE: (refer to TASK 21-53-12-300-803-A01) for replacement of the bearing.

(g)
Remove the Screws (05-190), the Flange (05-180) and the Seal (05-170).

(h)
Remove the Washers (05-210) and (05-200) and the Ball Bearing (05-220) from the Rotor Assembly (05-160).

NOTE: (refer to TASK 21-53-12-300-803-A01) for replacement of the bearing.

(i)
Remove the Rotor Assembly (05-160) from the Stator Crankcase Assembly (05-240).

Page 3006

CLEANING
TASK 21-53-12-100-801-A01
1.  ACTUATOR - CLEANING
A.  Reason For The Job
Self-Explanatory

B.  Job Set-Up Information
(1)
Tools, Features and Equipment

(a) Equivalent alternatives may be used for the listed items.

(2)  
Consumable Material

(a) Equivalent alternatives may be used for the listed items.

(3)  
Referenced Information
Not Applicable

REFERENCE  QTY  NAME 
As available  1  Soft brush (natural bristle) 
No specific  1  Dry compressed air supply source 

REFERENCE  NAME 
95° Ethyl Alcohol Turco Air Tech  No specific  Cleaning fluid Cleaning product Cloth (lint-free) 

C.  Job Set-Up Not Applicable
D.  Procedure
WARNING:  DO NOT GET CLEANING AGENTS ON YOUR SKIN, IN YOUR EYES OR NEAR A FLAM. DO NOT INHALE FUMES. USE ONLY CLEANING AGENTS IN A AREA WITH A GOOD FLOW OF AIR. OBEY LOCAL SAFETY AND HEALTH INSTRUCTION. CLEANING AGENTS ARE POISONOUS AND FLAMMABLE.
Page 4001
21-53-12  JUN 15/10
WARNING:  DISCONNECT THE EQUIPMENT FROM POWER SUPPLIES OR TEST EQUIPMENT BEFORE CLEANING.
CAUTION:  USE ONLY SPECIFIED CLEANING MATERIALS, OR THEIR EQUIVALENTS. THE SURFACE PROTECTION COULD BE DAMAGED IF UNSPECIFIED MATERIALS ARE USED.
CAUTION:  CLEANING METHODS SHALL BE CLOSELY OBSERVED OR REPLACED BY PROCEDURE SPECIFIED BY THE MANUFACTURER OF EQUIVALENT SUBSTITUTES. ON COMPLETION OF THE CLEANING STEPS, PARTS SHALL BE PROTECTED BY MEANS OF PROTECTIVE CAPS OR APPROPRIATE PACKAGING MATERIAL TO PREVENT CONTAMINATION BY DUST OR UNWANTED MATERIALS.
Subtask  21-53-12-140-001-A01
(1) External Cleaning of the unit
(a)
Clean all the metal parts using the specified cleanser, 95° Ethyl Alcohol cleaning fluid and a lint-free cloth.

(b)
To clean the attaching parts, put them into a solvent solution and dry them with low-pressure air jet (Dry compressed air supply source).

(c)
Loosen dust and unwanted material from the electrical parts and mating surfaces using cleanser and a soft brush (natural bristle). Dry the electrical parts using a clean low pressure air jet (Dry compressed air supply source) or a clean and soft lint-free cloth.

Subtask  21-53-12-140-002-A01
(2) Internal cleaning of the unit
(a)
Mechanical component cleaning 1 If necessary, clean the surface of parts to which Mastinox has been applied with Turco Air Tech Cleaning product or equivalent. 2 Clean all the other metal parts using the specified cleanser, 95° Ethyl Alcohol cleaning

fluid and a lint-free cloth. 3 Dry parts with low-pressure air jet (Dry compressed air supply source).

(b)
Electrical parts cleaning 1 Use a soft brush (natural bristle) and a clean dry low pressure air jet (Dry compressed

air supply source) to remove dust from each electrical part.
2

Take care not to damage the protective coating.
3

Clean each part with a lint free cotton cloth.
(c) New component cleaning
1

Remove all preservation material and make sure that the new component is fully clean and dry.
Page 4002

INSPECTION/CHECK
TASK 21-53-12-200-801-A01
1.  ACTUATOR -CHECK
A.  Reason For The Job
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(25)