TO: HOLDERS OF STANDARD PRACTICES MANUAL, ATA NO. 20-00-02/70-00-01, REVISION 6, DATED APRIL 23, 1999. APPLICATION: GENERAL
REVISION NO. 7, DATED APRIL 1, 2005 This is a COMPLETE revision. Pages revised are listed below, together with the Highlights of the revision. Do to the extent of the changes, this publication has been reprinted in its entirety. Please discard entire manual of previous issues and replace with this complete manual.
HIGHLIGHTS
Changed references from AlliedSignal to Honeywell throughout.
Changed headers and footers throughout.
Updated all Table of Contents to reflect revised and added procedures.
Updated List of Effective Pages to reflect revised and added procedures.

Reformatted cross-references for consistency. 
Adjusted all Table and Figure numbers as necessary. 
Subject/Page  Description of Contents 
Title Page  Revised to latest revision date. 
Record of Revisions  Added Revision 7 
List of Effective Pages  Revised to reflect changed pages. 
INTRODUCTION Page 1  Added "Workscope Planning Guides" to second paragraph. 
SECTION II - CLEANING Page 205  Added Method No. 202H.
 Page 206  Revised Method No. 203B per TR 20-31/70-31.
 Page 219  Revised note for Method No. 203R per TR 20-36/70-36.
 Pages 221 through 226  Added Method No. 203T and 203U per TR 20-30/70-30. Added Method No. 203V. 
SECTION III - INSPECTION Page 301  Revised text under Step A.
 Page 302  Revised text on Note following Step D.(4).
 Page 334  Added Table 306. 

Page 1 of 2
Highlights Apr 1/05
20-00-02/70-00-01

Subject/Page Page 335 Page 337 Pages 341 through 349
Pages 354 through 359
Page 360
Pages 361 through 364

SECTION IV - REPAIR Pages 409 through 410 Pages 417 through 421 Page 427 Page 430 Page 431 Page 443 Pages 448 through 450
Pages 451 through 456
Pages 468 through 481/482
SECTION VII - APPENDIX Page 725
Page 727
Page 729
Pages 731 and 732
Page 733
STANDARD PRACTICES MANUAL 20-00-02/70-00-01
HIGHLIGHTS (CONT)
Description of Contents
Added Paragrah G.(1)(d).
Added inspection for pins in wiring harness.
Added optional runout and tooth bearing pattern
check.
Corrected Step numbers.
Added Step N.
Added Step O.

Added Methods 1 through 9 of metal spray repair.
Added Method No. 403I, 403J, 403K, and 403L.
Added Note for Method 406A.
Added Method No. 406C per TR 20-39/70-39
Added Note and Caution for Method No. 407A.
Added Figure 404.
Modified Note for repairing welded parts. Added

Method No. 411A, 411B, and 411C.

Added Steps (1) and (2) to Method No. 412C.
Adjusted for number roll.
Added Steps 15 through 17.

Revised the balancing machine model in Table 705 per TR 20-43/70-43.
Added ethyl alcohol to Table 706 per TR 20-24/70-24.
Added lint free cloth to Table 706 per TR 20-25/70-25.
Added plastic abrasive media to Table 706 per TR 20-26/70-26.
Replaced solvent (Shell 360), added sodium hydroxide and vinyl masking tape to Table 706 per TR 20-32/70-32 and TR 20-27/70-27.
Page 2 of 2
Highlights Apr 1/05
20-00-02/70-00-01

STANDARD PRACTICES MANUAL
LIMITED DISTRIBUTION TO AUTHORIZED PERSONS ONLY
This document and all information and expression contained herein are the property of Honeywell Inc., are loaned in confidence, and may not, in whole or in part, be used, duplicated, or disclosed for any purpose without prior written permission of Honeywell Inc.  All rights reserved. Copyright Honeywell Inc. 1977, 1999, 2005.
This Publication was prepared by Honeywell Engines, Systems & Services
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：標準施工手冊 STANDARD PRACTICES MANUAL 20-00-02/70-00-01