C.  
References

 (1)  
06-42-00/201, Empennage Access Doors and Panels

 (2)  
24-22-00/201, Electrical Power - Control

 (3)  
29-11-00/201, Main (Left, Right, and Center) Hydraulic Systems

 D.  
Access

 (1)  
Location Zones 211/212 Control Cabin 311/312 Area Aft of Pressure Bulkhead to BS 1787.45

 (2)  
Access Panel
 311AL Forward Stabilizer Compartment

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-05
 ALL  ú ú 02 Page 207 ú Dec 20/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 E. Install the STCM (Fig. 201)
 S 432-024
 (1)  
Put the STCM in its correct position and install the bolts and washers to attach it to the airplane structure.

 S 432-025

 (2)  
Remove the plugs from the hydraulic lines and the caps from the ports.

 S 432-026

 (3)  
Connect the hydraulic lines to the STCM.

 S 432-027

 (4)  
Connect the electrical connectors.

 S 432-030

 (5)  
AIRPLANES WITH STAB TRIM LEVERS ON THE CONTROL STAND;
 connect the control rods to the servo levers.

 S 092-031

 (6)  
AIRPLANES WITH STAB TRIM LEVERS ON THE CONTROL STAND;
 remove rig pins E/ST1 and E/ST2.

 S 092-061

 (7)  
AIRPLANES WITH STAB TRIM LEVERS ON THE CONTROL STAND; do the Adjustment for the Servo Levers on the STCM that follows in this task.

 S 712-033

 (8)  
Do the test for the STCM that follows in this task.

 F.
Install the Solenoid Valve (Fig. 201)

 (1)  
Install a new o-ring on the solenoid valve.

 S 642-035

 (2)  
Lightly apply a layer of assembly lubricant or hydraulic fluid to all surfaces of a new gasket plate.

 S 432-034
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-05
 ALL  ú ú 02 Page 208 ú Sep 20/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 S 432-036
 (3)  
Put the gasket plate its correct position on the STCM.

 S 422-037

 (4)  
Put the solenoid valve in its correct position on the STCM.

 S 422-038

 (5)  
Install the bolts and washers to attach the solenoid valve to the STCM and tighten the bolts as follows:

 (a)
Tighten the bolts to 30-35 pound-inches (3.39-3.95 Nm).

 G.  
AIRPLANES WITH STAB TRIM LEVERS ON THE CONTROL STAND; Adjustment for the Servo Levers on the STCM

 S 492-039
 (1)  
Install rig pins E/ST1 and E/ST2.

 S 222-040

 (2)  
The servo levers are adjusted correctly if the conditions that follow are correct:

 (a)
The servo levers on each STCM are no more than 0.03 inch

 (0.76 mm) away from the index marks on the lever stop plate.
 S 832-041
 (3)  
If one or more of the servo levers are not adjusted correctly, do the steps that follow:

 (a)  
Disconnect the control rod from the servo lever that is not adjusted correctly.

 (b)  
Adjust the rod end until the servo lever aligns with the index marks.

 (c)  
Tighten the check nut.

 (d)  
Make sure you can see the end of the rod end through the inspection hole.

 S 832-042
 CAUTION:_______DO NOT MOVE THE LINKAGE WHEN YOU REMOVE THE RIG PIN. CENTERING SPRINGS MOVE THE LEVERS WHICH CAUSE THE LINKAGE TO MOVE WHEN A RIG PIN IS REMOVED.
 (4)  Remove rig pins E/ST1 and E/ST2, then install them again.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(63)