(2)  
Control Wheel Protractor Kit - A27021-29

 (3)  
Push/Pull Gage, 0 to 15 lb. range -Commercially Available

 (4)  
Gage Assembly - B27039-2 (Part of Elevator and Stabilizer Rigging Equipment, B27039-1)

 (5)  
Elastic Cord - Commercially Available

 B.
References

 (1)  
06-42-00/201, Empennage Access Doors and Panels

 (2)  
24-22-00/201, Electrical Power-Control

 (3)  
27-51-00/201, Trailing Edge Flap System

 (4)  
29-11-00/201, Main (Left, Right, and Center) Hydraulic Systems

 (5)  
34-11-00/201, Pitot-Static System

 C.
Prepare for the Tests

 (1)  
Supply electrical power (Ref 24-22-00/201).

 S 865-B54

 (2)  
Open these circuit breakers on the overhead panel, P11, and attach DO-NOT-CLOSE tags:

 (a)  
11C6, CSEU 1L AC
 or FLT CONT ELEC 1L AC

 S 865-B53
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-00
 ALL  ú ú 02 Page 527 ú May 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 (b)  
11C8, CSEU 2L AC
 or FLT CONT ELEC 2L AC

 (c)  
11G17, CSEU 1R AC
 or FLT CONT ELEC 1R AC

 (d)  
11G27, CSEU 2R AC
 or FLT CONT ELEC 2R AC

 S 015-B55
 WARNING:_______STAY OFF SERVICE ACCESS DOORS 311AL AND 313AL. THE WEIGHT OF A PERSON CAN CAUSE THE SPRING-LOADED LATCHES TO RELEASE. A PERSON CAN BE INJURED IF THEY FALL THROUGH THE OPEN DOOR.
 (3)  Open the access door, 311AL, to the forward stabilizer-compartment (Ref 06-42-00/201).
 S 865-B56
 WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES
_______ WHEN HYDRAULIC POWER IS SUPPLIED. AILERONS, ELEVATORS, RUDDER, FLAPS, SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED SURFACES. INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN HYDRAULIC POWER IS SUPPLIED.
 (4)  
Pressurize the right and center hydraulic systems
 (Ref 29-11-00/201).

 D.
Electrical Travel Limits - Functional Test

 NOTE: The stabilizer may not be in electrical control range if it
____ does not move when the stabilizer-trim control-wheel-switches are moved in one direction. Move the stabilizer-trim control-wheel-switches in the other direction to move the stabilizer into electrical control range, then continue with test.
 S 215-C03
 (1)  
Make sure that the trailing edge flaps and the leading edge slats are in the fully retracted position.

 (2)
Make sure that the flap lever is in the zero detent (FLAPS UP).

 S 215-C04
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-41-00
 ALL  ú ú 02 Page 528 ú May 28/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

 S 865-C05
 WARNING:_______ KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES
 WHEN HYDRAULIC POWER IS SUPPLIED.  AILERONS, ELEVATORS, RUDDER,
 FLAPS, SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED
 SURFACES.  INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR

 WHEN HYDRAULIC POWER IS SUPPLIED.
 (3)  
Pressurize the left hydraulic system (Ref 29-11-00/201).

 S 865-C06

 (4)  
Put the RIGHT STAB TRIM SHUTOFF switch on the P10 panel to CUTOUT.

 S 865-C07

 (5)  
Move the captain's stabilizer-trim control-wheel-switches up (airplane nose down) and hold the switches up until the stabilizer stops.

 S 865-C08

 (6)  
Put the CENTER STAB TRIM SHUTOFF switch on the P10 panel to CUTOUT.

 S 215-C09

 (7)  
Make sure that dimension B on the stabilizer jackscrew is

 20.43 to 21.03 inches (519.0-534.1 mm) (Fig. 502).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 4(15)