FLOOR PROXIMITY LIGHTING RACEWAY
CAUTION: MAKE SURE THE WIRES ARE IN THE (EXAMPLE)
1
CENTER OF THE TRACK COVER. YOU CAN CAUSE DAMAGE TO THE WIRES IF THE WIRES ARE NOT IN THE CENTER OF THE TRACK COVER.
Floor Proximity Raceway Installation Figure 401
L89087
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH FLOOR PROXIMITY ESCAPE ú
25-27-31
PATH LIGHTING RACEWAYS ú ú 01 Page 402 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL
BOND FILLER STRIP TO BASE TRACK ALONG ENTIRE LENGTH OF
POST MODIFICATION
BOTH SIDES OF 1.5 INCH (38 mm) STRIP
PRE MODIFICATION
(TYPICAL)
Embodiment Instructions - Modified End Fitting
Figure 402
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH FLOOR PROXIMITY ESCAPE ú
25-27-31
PATH LIGHTING RACEWAYS ú ú GUN Page 403 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
L89101
A
757
MAINTENANCE MANUAL
TASK 25-27-31-404-009
3. Floor Proximity Path Lighting Raceway - Installation (Fig. 401)
____________________________________________________
A. Consumable Materials
(1)
G02129 Permacel - Silver Tape, P29
(2)
G01356 Tape - Doubleback, Orcon BMS 5-133
(3)
A01068 Adhesive, URALANE5774AB
(4)
B00130 Solvent, Isopropyl Alcohol, TT-I-735
(5)
Abrasive Paper, 80 grit or finer
B. References
(1)
AMM 25-25-01/201, Passenger Seats
(2)
AMM 25-27-01/401, Floor Covering
(3)
AMM 33-59-00/201, Floor Proximity Emergency Lights
C. Access
(1) Location Zone
200 Upper Half of Fuselage
D. Embodiment Instructions (Fig. 402)
S 014-010
(1)
Remove filler strip adjacent to the light assembly at the end of the floor strip.
S 854-011
(2)
Cut 1.5inches(38mm) off the end of the filler strip.
S 414-012
(3)
Re-fit the larger part of the filler to the floor strip.
S 824-013
(4)
Move the end light assembly to butt up to filler strip.
S 914-014
(5)
Bond the 1.5 inch (38mm) section of filler strip to the base track between the end light assembly and the end cap using URALANE5774AB ashesive as follows:
NOTE: Refer to SAK Screen on time for health and safety
____
information.
(a)
Clean both surfaces to be bonded with IPA solvent (part no. IPA).
(b)
Lightly sand with 180 grit or finer paper.
(c)
Wipe dry.
(d)
Bond in place with URALANE5774AB adhesive. 1) Mix 100 parts of part A with 55 parts of part B by weight.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH FLOOR PROXIMITY ESCAPE ú
25-27-31
PATH LIGHTING RACEWAYS ú ú 01 Page 404 ú May 28/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757 MAINTENANCE MANUAL
2) Mix thoroughly for 2 minutes and use within 20 minutes.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 EQUIPMENT/FURNISHINGS 1(75)
