S 117-055
 WARNING: DO NOT GET SOLVENTS IN YOUR MOUTH, OR YOUR EYES, OR ON YOUR
_______ SKIN. DO NOT BREATHE THE FUMES FROM SOLVENTS. SOLVENTS ARE HAZARDOUS MATERIALS. REFER TO PRODUCT MATERIAL SAFETY DATA SHEETS (MSDS) AND LOCAL REQUIREMENTS FOR PROPER HANDLING PROCEDURES.
 CAUTION: DO NOT LET THE SOLVENT TOUCH THE PLASTIC FOR A LONG TIME.
_______ DAMAGE TO THE SURFACE CAN OCCUR IF YOU ARE NOT CAREFUL WITH THE SOLVENT.
 (1)  
Fully rub the surface with a cheesecloth that is moist with MEK , or solvent, Series 98 (AMM 20-30-98, SOPM 20-30-98).

 S 147-030

 (2)  
Dry the surface with a clean, dry cloth before the solvent dries.

 S 957-031

 (3)  
Apply the masking tape on the adjacent surfaces.

 S 377-032

 (4)  
Apply the BMS 10-83, type I primer to the surfaces you will paint.

 S 377-033

 (5)  
Mix the polyurethane paint, of the correct color.

 NOTE: Obey the manufacturers instructions.
____
 S 377-034
 (6)  
Apply the cross-layers of paint to get the same color as the adjacent area. This is the base layer.

 (7)  
Remove the masking tape.

 S 957-035
 NOTE: Let the base layer dry for 2 hours at 70 to 80°F before you
____ touch the paint. Let the base layer dry for 1 hour before you apply a texture layer.
 S 377-036
 (8)  If it is necessary, apply a texture layer of the same paint that is not thin.
 NOTE: Let it dry 3 hours before you touch it.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 25-00-00
 ALL  ú ú 01 Page 717 ú Sep 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 E. Procedure - Paint the Polycarbonate (Lexan) Surfaces (where applicable)
 S 117-037
 (1)  
Clean the surface with a cheesecloth that is moist with mixed detergent.

 S 147-038

 (2)  
Rub the surface lightly with 180-grit (minimum) abrasive paper to remove gloss.

 S 117-039

 (3)  
Clean the surface with a cheesecloth that is moist with mixed detergent.

 S 357-040

 (4)  
Examine the surface for surface defects. If you find surface defects, do the steps that follow:

 (a)  
Put putty on a clean cheesecloth at package consistency.

 (b)  
Rub the surface with the cheesecloth to push the putty into the surface defects.

 (c)  
Let the putty dry for 3/4 to 1 hour.

 (d)  
Remove the unwanted putty with abrasive paper.

 (e)  
Clean the surface with a cheesecloth that is moist with mixed detergent.

 S 377-047
 CAUTION:_______DO NOT USE PAINTS WHICH CONTAIN SOLVENTS. PAINTS WHICH CONTAIN SOLVENTS CAN CAUSE DAMAGE TO POLYCARBONATE SURFACES.
 (5)  Apply the polyurethane paint. Refer to the steps given before for use of polyurethane paints.
 F.  Procedure - Paint the Textured Finishes (door linings and escape slide covers where applicable)
 S 117-042
 (1)  
Clean the area you will paint with BMS 3-2 solvent or aliphatic naphtha.

 (2)  
Apply the masking tape to the adjacent surfaces.

 (3)  
Apply the Hi-Speed lacquer, that is not thin, with a brush.

 S 377-045

 (4)  
Touch the wet paint with a brush that has short, rigid bristles to make the surface look textured.

 S 957-043
 S 377-044
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 25-00-00
 ALL  ú ú 01 Page 718 ú May 28/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757 MAINTENANCE MANUAL
 EQUIPMENT/FURNISHINGS - APPROVED REPAIRS
________________________________________
 1.  General_______
 A.  This procedure contains instructions to do approved repairs on the following items:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 EQUIPMENT/FURNISHINGS 1(12)