79-21-09
 ALL  ú ú N02 Page 410 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 024-019-N00
 (22) Remove the air/oil heat exchanger (1) and valve (18) from the engine with the steps that follow:
 (a)  
Sufficiently pull out the air/oil heat exchanger (1) to lower the lower bracket (21) between the intermediate case and flange on the fan exit liner.

 (b)  
Turn out the higher end of the air/oil heat exchanger (1) until the higher bracket (29) is away from the flange of the fan exit liner.

 WARNING: DO NOT HOLD THE VALVE BY THE INLET COLLARS, WHICH ARE NOT
_______ PARTS OF THE VALVE DUCTS. THE INLET COLLARS CAN BREAK OFF. IF YOU HOLD THE VALVE DUCTS BY THE INLET COLLARS, YOU CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (c)  
Lift up and pull out the air/oil heat exchanger (1) and valve (18) from the intermediate case.

 (d)  
Discard the packings (15).

 (e)  
Install the protection caps.

 S 034-020-N00
 (23) If it is necessary, remove the valve (18) from the heat exchanger (1) with the steps that follow:
 (a)  
Put the air/oil heat exchanger (1) and valve (18) assembly on a clean, flat surface.

 (b)  
Remove the jamnuts (44) and, if installed, washers and the plate or bolts which attach the servo fuel drain (40), supply (41), and return tubes (42) to the bulkhead on the heat exchanger (1).

 (c)  
Remove the bolts (32), nuts (30), and washers (31) from the mating flange of the valve (18) and the heat exchanger (1).

 (d)  
Remove the valve (18) from the heat exchanger (1).

 S 034-021-N00
 (24) If it is necessary to install a new valve (18), do the steps that follow:
 (a)  
Remove the bolt(s) (38), nut (39), and clamps (37 and 43) which attach the servo fuel supply tube (41) to the servo fuel drain tube (40).

 (b)  
Remove the servo fuel drain (40), supply (41), and return (42) tubes from the adapters (34, 36).

 (c)  
Remove the three adapters (34, 36) from the valve ports.

 (d)  
Discard the packings (33, 35).

 (e)  
Install the protection caps on all openings.

 S 034-023-N00
 (25) If it is necessary to install the new heat exchanger (1), do the steps that follow:
 (a) Remove the short bolts (17) which attach the higher (29) and lower (21) mounting brackets to the heat exchanger (1).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-21-09
 ALL  ú ú N02 Page 411 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(b)  Remove the higher (29) and lower (21) mounting brackets.
 TASK 79-21-09-404-024-N00
 3. Install the Engine Air/Oil Heat Exchanger and Valve (Fig. 401)
___________________________________________________
 A. Equipment
 (1)  
PWA 85853 - Torque Adapter, Pratt & Whitney, Commercial Products Division, 400 Main Street, East Hartford, CT 06108

 (2)  
PWA 87505 - Positioner, Pratt & Whitney, Commercial Products Division, 400 Maij Street, East Hartford, CT 06108

 (3)  
M303, M305, or M307 Bergen Mechanical Crimper
 Bergen Cable Technologies Inc
 170 Gregg St

 P.O.
 Box 1300
 Lodi, NJ 07644-9982

 B.
Consumable Materials

 (1)  
D00250 Petrolatum - White, VV-P-236

 (2)  
D00390 Oil - Engine

 (3)  
G02332 Ferrule, Safety Cable (P05-292)

 (4)  
G02334 Lockwire, (P05-289) 0.032 inch (0.813 mm) - AS3214-02

 (5)  
G02335 Cable, Safety (P05-291)

 (6)  
G00964 Compound - Antigalling, Fel-Pro C-200

 C.
Parts

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 79-21-09
 ALL  ú ú N02 Page 412 ú Feb 18/00
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊 滑油 OIL(66)