(2)
AMM 27-62-00/201, Speed Brake Control System
(3)
AMM 27-81-00/201, Leading Edge Flap System
(4)
AMM 29-11-00/201, Main Hydraulic Supply System
(5)
AMM 71-11-04/201, Fan Cowl Panels
(6)
AMM 78-31-00/201, Thrust Reverser System
(7)
AMM 78-36-01/401, Thrust Reverser Proximity Sensors
(8)
AMM 78-36-01/401, Thrust Reverser Proximity Sensors
(9)
IPC 78-31-01 Fig. 10
E.
Access
(1)
Location Zone 415 and 416 Engine 1 - Thrust Reverser Halves 425 and 426 Engine 2 - Thrust Reverser Halves 435 and 436 Engine 3 - Thrust Reverser Halves 445 and 446 Engine 4 - Thrust Reverser Halves
(2)
Access Panel
413 and 414 Fan Cowl Panels - Engine 1
423 and 424 Fan Cowl Panels - Engine 2
433 and 434 Fan Cowl Panels - Engine 3
443 and 444 Fan Cowl Panels - Engine 4
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
78-31-17
ALL ú ú N02 Page 428 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
F. Install the Non-Locking Hydraulic Actuator for the Thrust Reverser
S 864-049-N00
(1)
Make sure the DO-NOT-OPERATE tags are installed on the forward thrust lever and reverse thrust lever.
S 864-050-N00
(2)
Make sure the thrust reverser sleeve is in the position
approximately one inch or less of the full stow position.
S 984-123-N00
(3)
If it is necessary, turn the flexshaft drive with a 3/16 inch (5.0 mm) square drive in the direction that fully retracts the actuator rod end.
S 224-051-N00
(4)
Make sure the distance (dimension A in Fig. 401) between the rod end collar and actuator cylinder is between 0.010-0.018 inch before the installation.
NOTE: A distance of 0.010-0.018 inch shows the full retract
____ position and is set when the hydraulic actuator is repaired on the bench rig. Reject the hydraulic actuator if the clearance is not satisfactory.
S 424-124-N00
CAUTION: DO NOT LET THE ROD END OF THE HYDRAULIC ACTUATOR TURN OR BE
_______ TURNED WHEN YOU CONNECT IT TO THE THRUST REVERSER SLEEVE. IF THE ROD END IS TURNED, IT CAN CAUSE DAMAGE TO THE ACTUATOR.
(5) Install the non-locking hydraulic actuator (3 or 7) (Fig. 403 or 404), with the rod end first, through the opening in the torque box.
(a) Align the hydraulic ports with the hydraulic tubes.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
78-31-17
ALL ú ú N02 Page 429 ú Oct 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 434-053-N00
(6) Install the bolt (5), washers (6), nut (7), and cotter pin (9) which hold the rod end (2 or 5) to the thrust reverser sleeve (Fig. 401). (a) Tighten the castellated nut (7) to 20 pound-inches (2.66 newton-meters). (b) Tighten the nut (7) to the subsequent castellation. (c) Install the cotter pin (9). (d) Apply the sealant to the end of the bolt (5), nut (7) and cotter pin (9) to approximately 0.06 inch (1.5 mm) thickness.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 EXHAUST 2(44)
