Variable Stator Vane Actuator Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-02
ALL ú ú N02 Page 403 ú Feb 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
S 864-004-N00
(3)
Push the STAT button on the EICAS display select panel.
(a)
Make sure the status page shows on the auxiliary EICAS.
(b)
Make sure the applicable FUEL SPAR VLV 1, 2, 3, or 4 status message does not show.
___
S 864-005-N00
(4)
For the applicable engine, open these circuit breakers and install the DO-NOT-CLOSE tags:
(a)
P6 Main Power Distribution Panel
1) 6G1 FUEL SHUTOFF VALVE ENG 1
2) 6G15 SCU ALT PWR ENG 1
3) 6G23 ENG SCU 1
4) 6G2 FUEL SHUTOFF VALVE ENG 2
5) 6G16 SCU ALT PWR ENG 2
6) 6G24 ENG SCU 2
7) 6G3 FUEL SHUTOFF VALVE ENG 3
8) 6G17 SCU ALT PWR ENG 3
9) 6G25 ENG SCU 3
10) 6G4 FUEL SHUTOFF VALVE ENG 4
11) 6G18 SCU ALT PWR ENG 4
12) 6G26 ENG SCU 4
S 014-041-N00
(5) Open the right fan cowl panel (AMM 71-11-04/201).
S 044-053-N00
WARNING: DO THE THRUST REVERSER DEACTIVATION PROCEDURE TO PREVENT THE
_______ OPERATION OF THE THRUST REVERSER. THE ACCIDENTAL OPERATION OF THE THRUST REVERSER CAN CAUSE INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT.
(6)
Do this procedure: Thrust Reverser Deactivation for Ground Maintenance (AMM 78-31-00/201).
(7)
Open the right core cowl panel (AMM 71-11-06/201).
S 014-042-N00
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
75-31-02
ALL ú ú N02 Page 404 ú Jun 18/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
S 014-054-N00
WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 WHEN YOU OPEN THE
_______ THRUST REVERSERS. IF YOU DO NOT OBEY THE INSTRUCTIONS, INJURIES TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR.
(8)
Open the right thrust reverser (AMM 78-31-00/201).
F.
Procedure
S 024-060-N00
(1) Remove the variable stator vane actuator:
(a)
Disconnect the electrical connectors (17 and 18) from the actuator (7). 1) Install the protection caps.
(b)
Remove the bolt (19) which attaches the ground cable (20) for the actuator (7).
(c)
Put the container below the actuator (7) to catch the remaining fuel.
(d)
Disconnect the tube nuts which attach the servo fuel supply tube (10), servo fuel return tube (11), and drain hose (13) to the actuator (7).
(e)
Remove the drain tube (29) below the actuator (7) with the steps that follow: 1) Put the container below the drain tube tee. 2) Disconnect the tube nut (28) at the forward tee connection
for the drain tube. 3) Remove the screw (31), nut (32), and washer (33) which
attach the drain tube clamp (30) to the bracket. 4) Disconnect the tube nut from the union (34). 5) Remove the drain tube (29) from the engine.
(f)
Remove the cotter pin (2), nut (1), washer (3), and shoulder bolt (4) which attach the rod end bearing (5) to the bellcrank. 1) Discard the cotter pin (2).
(g)
ENGINES PRE-PW-SB 72-498; Remove the cotter pin (23), nut (24), bolt (25), and bearing stop (27) from the two sides of the support bracket for the actuator (7).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 大氣 AIR 2(45)
