(2)  
SSM 52-34-01, 52-35-01

 (3)  
WDM 52-34-11, 52-35-11

 F.
Access

 (1)  
Location Zone 122 Forward Cargo Container Compartment, Forward Half 142 Aft Cargo Container Compartment

 (2)  
Access Panel
 821R Door - Forward Cargo Compartment
 822R Door - Aft Cargo Compartment

 G.
Procedure

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-07
 ALL  ú ú 01 Page 406 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 984-011
 CAUTION:_______ USE A TORQUE WRENCH WITH A DIAL INDICATOR TO FIND WHEN ACTUATOR
 INTERNAL STOPS ARE TOUCHED.  DO NOT USE MORE THAN 25
 POUND-INCHES.  IF YOU USE MORE THAN 25 POUND-INCHES, YOU CAN

 CAUSE INTERNAL DAMAGE TO THE HOOK ACTUATOR.
 (1)  
Do these steps to set the hook actuator in the rigged closed position:

 (a)  
Manually turn the hook actuator clockwise to the internal stops.

 (b)  
Examine the torque. When the torque increases by 15-20 pound-inches, the internal stops are touched.

 (c)  
Turn the hook actuator 2 1/2 turns counterclockwise.

 NOTE: This is the rigged closed position.
____
 S 424-012
 (2)  
Install the hook actuator on the door as follows (Fig. 401):

 (a)  
Apply grease to the splined male drives of the hook actuator.

 (b)  
Adjust the pushrod (12), if it is necessary, to make sure the torque tube (1) engages the hook actuator (3).

 (c)  
Clean the mating surfaces to make an electrical bond at one of the bolt locations.

 (d)  
Install the hook actuator (3) on the support bracket (2).

 (e)  
Use a bonding meter to measure the electrical resistance across the bond (Ref 20-22-01/601).

 NOTE: The maximum resistance must not be more than 0.0025
____ ohms.
 S 434-013
 (3)  
Install the torque tube (4) on the splined shaft of the actuator (3) as follows:

 (a)  
Push the torque tube (4) on the actuator output shaft, install the coupling (11) and hold it tightly with the two clamps (5).

 (b)  
Remove the two LCD-1 rig pins.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-07
 ALL  ú ú 01 Page 407 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

INTERNAL  INTERNAL

(M + 15)
MANUAL DRIVE TORQUE

M

TURNS OF MANUAL DRIVE TORQUE WRENCH

NOTE:  THE TURNS ARE THE NUMBER OF TURNS OF A TORQUE WRENCH IN THE MANUAL DRIVE. COUNT THE TURNS AFTER YOU FIND THE INTERNAL STOPS.

USE A TORQUE WRENCH TO FIND THE
INTERNAL STOPS OF THE ACTUATOR AS FOLLOWS:

1.  
MEASURE THE TORQUE (M) WHILE YOU MANUALLY TURN THE ACTUATOR.
(THE TORQUE SHOULD BE CONSTANT WITHIN |2 POUND-INCHES).

2.  
TURN THE ACTUATOR UNTIL THE TORQUE INCREASES BY 15-20 POUND-INCHES (M + 15).

3.  
TURN THE ACTUATOR 1/2-TURN IN THE OPPOSITE DIRECTION FROM THE (M + 15) POINT.

4.  
THE INTERNAL STOPS ARE AT THIS POINT.

Actuator Internal Stop and Rig Positions
Figure 402

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-07
 ALL  ú ú 02 Page 408 ú Oct 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 434-022
 (4)  
If it is necessary, connect the hook return spring.

 (a)  
Rotate the return spring counter-clockwise and install the spring attach bolt.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 3(76)